Related Manuals for Fishman FLUENCE Series
Summary of Contents for Fishman FLUENCE Series
- Page 1 INSTALLATION GUIDE FLUENCE MIKE INEZ LEGACY SERIES SET FLUENCE MIKE INEZ LEGACY SERIES SET INSTALLATION GUIDE...
-
Page 2: System Requirements
TARILY ASSUME THE RISK OF DEATH OR OTHER PERSONAL INJURY SUSTAINED WHILE PARTICIPATING IN SUCH ACTIVITIES WHETHER OR NOT CAUSED BY THE NEGLIGENCE OR ANY OTHER FAULT of Fishman, including but not limited to equipment malfunction from whatever cause, or any other fault of Fishman. Additionally, you agree to indemnify, defend... -
Page 3: Getting Started
Test fit the components to make sure that each will fit in the allocated locations or modify the instrument until the fit is correct and all controls can be located without issue. Fishman Fluence Pickups are active and require 25K audio taper potentiometers. - Page 4 4. Review your planned scheme for errors, complete the soldering, mount and secure all your components, and test your completed installation before assembly. Consider a popular wiring option as shown on the reverse side of this guide or visit www.fishman.com for additional wiring diagrams.
- Page 5 Mike Inez Signature: Voice – 1: (2.6kHz, 40Hz) From Ozzy to Alice and beyond, this is THE tone. Voice – 2 Mid Contour: (760Hz, 80Hz) For all of Mike’s warmer, more vintage tones. Fluence Soapbar (bridge): Voice – 1: (2kHz) Classic, Fat, and Round tone, use for all vintage type sounds, with- out excess high end string noise and with a fat low end that moves a lot of air.
- Page 6 Fluence Bass – Connection Points & Functions 1. Mid Flat - This feature bypasses the mid contour on Voice 2, and Rev3.1 works in both Humbucking and Single Coil mode. BASS-SB1 To activate, connect the Mid Flat wire to ground, either wired through a switch or permanently to a ground source within the cavity.
- Page 7 Note: the Single Coil select pin does not override the Voice select. Therefore, you are free to use the single coil mode with Voice 1, Voice 2, and Voice 2 Mid Flat 3. Single Coil Select Wire - To select Single Coil mode, connect this pin to ground through a switch contact.
- Page 8 9V supply, however they are 18V compatible for instruments already set up that way. 6. Output - The main output pin has a 8.2k ohm output impedance and is suitable for driving low impedance volume and tone pots, typically 25k. Wiring diagrams are available at Fishman.com...
- Page 9 9V Battery Mike Inez - Legacy Bass Pickup Volume w 2-Band Dual Concentric EQ - Pull Volume for Voice-2 Neck Pickup Mike Inez Legacy Bridge GND Volume Rev2.1 Default: Mike Inez Main Voice-1 Pull for Voice-2 Ring Sleeve Used Mike Inez - Bass 4-String Bridge 4-String Neck 5-String Bridge...
- Page 10 9V Battery Mike Inez - Legacy Bass Pickup Volume w 2-Band EQ - Pull Volume for Voice-2 Neck Pickup Mike Inez Legacy Bridge GND Volume Rev2.1 Default: Mike Inez Main Voice-1 Pull for Voice-2 Ring Sleeve Used Mike Inez - Bass 4-String Bridge 4-String Neck 5-String Bridge...
- Page 11 9V Battery Mike Inez - Legacy Bass Pickup Set Volume & Blend Control w 2-Band EQ - Pull Volume for Mike Inez Alt. Voice & Bridge Voice-1 Neck Pickup Bridge Pickup Mike Inez Legacy Fluence SB-1 Bridge GND Rev2.1 Rev3.0 BASS-SB1 Volume * Ring...
- Page 12 9V Battery Mike Inez - Legacy Bass Pickup Set Volume & Blend Control w 2-Band EQ - Mini Toggle Voice Select Neck Pickup Bridge Pickup Mike Inez Legacy Fluence SB-1 Bridge GND Rev2.1 Rev3.0 Volume BASS-SB1 (Pull for Single Coil Mode) Output Ring Jack...
- Page 16 Fishman and Fishman Transducers are trademarks or tradenames of Fishman Transducers Inc. 514-300-179_r0 7/19...