Advertisement
Quick Links
Advertisement
Related Manuals for JRC JLR-7500
Summary of Contents for JRC JLR-7500
- Page 1 NA11ZZ0920C GPS NAVIGATOR PROGRAM UPDATE PROCEDURE...
- Page 2 NA11ZZ0920C Updating The display unit program can be updated with the aid of an externally connected PC. A PC and connection cable are necessary for updating the programs. Before an update can be performed, the current setting values must be recorded. (Enter the values into the lists at the end of this manual.) ...
- Page 3 NA11ZZ0920C NWZ-4740 Display Unit Update Procedure Preparation 1.1. Prepare the following: PC OS: Windows95 / 98 / NT / 2000 / XP / VISTA(Home Premium) Available hard disk space required: 10MB or more COM port: If the PC does not have a COM port, prepare a USB serial conversion adapter. ...
- Page 4 NA11ZZ0920C Running the Update Program 2.1. Switch the NWZ-4740 to the maintenance mode. To switch to the maintenance mode: 1. Press to display the MAIN MENU. 2. Hold down together until [0. EQUIP SET] is displayed. 2.2. Select [8. SOFT UPDATE] in the EQUIP SET menu. Select DISPLAY for [1.
- Page 5 NA11ZZ0920C 2.4. Select Com Port , and then the connected COM port number and bit rate. The same bit rate as the NWZ-4740 must be selected. COM Setting Bit Rate Setting 2.5. Click the 1. File select button and select the update file (xxxxxx.bin). Check that the message "File select ok."...
- Page 6 NA11ZZ0920C 2.6. Click the 2. Load file button, and check that the message "The BIN file loading ok." is displayed. 2.7. Click the 3. Write mode button, and check that the following is displayed instantly on the NWZ4740 FLASH 1 screen. ->...
- Page 7 NA11ZZ0920C 2.9. Check that the progress bar reaches the end and 100% is displayed for "Percent," and that the message "Upgrading succeeded" is displayed in the Msg box. Update is normally finished when this message is displayed. 2.10. If "Upgrading succeeded" is not displayed or another message is displayed in the Msg box, the update has failed, so try the update again.
- Page 8 NA11ZZ0920C Appendix MEMO MENU SETTING CONTRAST 1 2 3 4 5 6 7 8 9 10 11 12 13 DISPLAY DIMMER MAXIMUM 1 2 3 4 5 6 7 8 9 10 TYPICAL 1 2 3 4 5 6 7 8 9 10 MINIMUM 1 2 3 4 5 6 7 8 9 10 CLICK SOUND...
- Page 9 NA11ZZ0920C MENU SETTING TRANSFER OUT CONNECT MULTICAST UNICAST BROADCAST WPT / WPT / TO IP ROUTE ROUTE PORT No. (LAN) FORMAT SHARE Ver1.5 Ver2.1 Ver2.3 ALL WPT ALL ROUTE ALL WPT+ROUTE TYPE ROUTE ROUTE+WPT TRACK EVENT/MARK FROM IP ／ DEFAULT WIDTH PORT [NM] SETTINGS...
- Page 10 NA11ZZ0920C MENU SETTING GPS MODE AUTO GPS ALONE SBAS GPS / BEACON BEACON / FIX MODE AUTO SBAS SAT ELV MASK [°] HDOP SMOOTHING POSITION [sec] SPEED [sec] COURSE [sec] RAIM ACCURACY LEVEL LATITUDE INITIALIZATION LONGITUDE ANT HEIGHT BEACON / STATION AUTO MANUAL...
- Page 11 [m] ／ LENGTH BEAM SENSOR ENABLE DISABLE [m] ／ Y CCRP ENABLE DISABLE [m] ／ Y DATA I/O DATA SETTING NMEA JRC IEC ROUTE PRINTER SWITCH IN/OUT1 VERSION Ver1.5 Ver2.1 Ver2.3 BITRATE 4800 9600 19200 38400 SENTENCE GGA : RMC :...
- Page 12 NA11ZZ0920C EQUIP MENU SETTING DATA I/O DATA SETTING NMEA ROUTE SWITCH OUT3 VERSION Ver1.5 Ver2.1 Ver2.3 BITRATE 4800 9600 19200 38400 SENTENCE GGA : RMC : GLL : VTG : GSA : GSV : DTM : GBS : GRS : GST : ZDA : GNS :...
- Page 13 NA11ZZ0920C EQUIP MENU SETTING DATA I/O DATA OUT MULTICAST UNICAST BROADCAST TO IP PORT NO FORMAT : Ver1.5 Ver2.1 Ver2.3 GGA : RMC : GLL : VTG : GSA : GSV : DTM : GBS : GRS : GST : ZDA : GNS : MSS :...