Advertisement
Quick Links
Quick start guide
for models LS6125/LS6125-2/
LS6125-3/LS6125-4/LS6125-5/
LS6126-3/LS6126-5
Install the telephone base and
charger(s)
Install the telephone base and charger(s) as
shown below.
Telephone
Telephone base
wall jack
power adapter
(large)
DSL filter (not
included) required
if you have DSL
high-speed
Internet service
Electrical outlet
Telephone line cord
not controlled
by a wall switch
Charger
Telephone base
NOTES:
1.
Use only the power adapter(s) and
battery(ies) supplied with your VTech
telephone.
2.
For complete feature instructions,
please refer to your user's manual.
Bat te r y inst allation and
charging
Install the battery as shown below. After
installing the battery, you might be able
to make and receive short calls. For best
performance, charge the handset battery for
at least 16 hours before use.
1
2
Plug the battery securely
Place the battery with the
label THIS SIDE UP facing
into the plug inside
the handset battery
up and the wires inside
compartment, matching
the battery compartment.
the color-coded label.
Charger
adapter
(small)
3
4
Charge the handset by
Align the cover flat
against the battery
placing it in the telephone
compartment, then slide
base or charger. The
CHARGE light will be
it upwards until it clicks
into place.
on when the handset is
charging.
VOL
CID
FLASH
Make, answer and end a call
Make a call
/FLASH or
1.
Press
2.
Dial the number.
-OR-
1.
Dial the number.
2.
Press
/FLASH or
Answer a call
•
Press
/FLASH,
keys (0-9, #, * ).
End a call
•
Press OFF/CLEAR or put the handset in
the telephone base or charger.
Activate the answering system
The answering system must be turned on
to answer and record messages. Press
ANS ON/OFF to turn the answering system
on or off. When the answering system is
turned on, it will announce "Calls will be
answered," and the ANS ON/OFF light will be
on. When the answering system is turned off,
CHARGE light
it will announce "Calls will not be answered,"
and the ANS ON/OFF light will be off.
MENU
SELECT
CLEAR
Outgoing announcement
The telephone is preset with a greeting that
answers calls with "Hello, please leave a
.
message after the tone." You can use this
preset announcement, or replace it with
your own.
To record your own announcement:
.
1.
Press ANNC while the telephone is not
in use and the system will announce
"Announcement. Press PLAY or press
RECORD."
2.
Pr e s s R E C O R D a n d t h e s y s t e m
announces, "Record after the tone. Press
STOP when you are done."
3.
Af ter the tone, speak towards the
microphone at the bot tom front of
the telephone base from about nine
or any of the dialing
inches away.
4.
Press
/PLAY/STOP when finished.
5.
The answering system will automatically
play the newly recorded announcement.
Press
/PLAY/STOP to stop the playback
at anytime.
To play messages:
•
Press PLAY/STOP to play messages and
stop playback.
Press X/DELETE while a message is
•
playing to delete it.
Press /SKIP to skip to the next message.
•
/REPEAT to repeat the current
•
Press
message.
Press VOL / to raise or lower playback
•
volume.
IMPORTANT!
If your product is not working properly:
Refer to the Troubleshooting section of
•
the user's manual.
•
Visit our website at www.vtechphones.
com or call 1 (800) 595-9511. In Canada,
go to www.vtechcanada.com or 1 (800)
267-7377.
96-006809-010-100
Advertisement
