Yamaha Disklavier Silent Mark III Service Manual page 134

Table of Contents

Advertisement

00000001
01
= Sub-ID #2=General MIDI On
11110111
F7
= End of Exclusive
When General MIDI Mode On is received. the play mode will
be changed to XG mode.
When this happens, the ESBL part will receive the MIDI
messages which compatible with GM System Level 1, and
consequently will not receive NRPN and Bank Select messages.
Since approximately 50ms is required to execute this messag, be
sure to leave an appropriate interval before the subsequent
message.
2.1.4
XG  Native  Parameter  Change
(ESBL Part)
With the Parameter Change messages as listed below, you can
change the characteristic of a Voice, such as by Effect Type or
effect parameter, transpose, tuning, and others.
11110000
F0
Exclusive status
01000011
43
YAMAHA ID
0001nnnn
1n
Device Number
01001100
4C
XG Model ID
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
0ddddddd
ddddddd
Data
|
|
11110111
F7
End of Exclusive
* Any number is OK since the device number for the Disklavier
is fixed to "All".
For parameters with data size of 2 or 4, transmit the appropriate
number of data bytes.
When sending the parameter change messages consecutively, be
sure to leave an appropriate interval (if the time base is 480. ca 5
unit) between the messages.
2.1.4.1
XG System On
(ESBL Part)
11110000
F0
Exclusive status
01000011
43
YAMAHA ID
0001nnnn
1N
Device Number
01001100
4C
XG Model ID
0aaaaaaa
00
Address High
0aaaaaaa
00
Address Mid
0aaaaaaa
7E
Address Low
00000000
00
Data
11110111
F7
End of Exclusive
When this data is received. the Disklavier will switch to XG
mode and all the parameters will be initialized accordingly, and
XG-compatible messages such as NRPN and Bank Select
messages can be received.
Since approximately 50ms is required to execute this message,
be sure to leave an appropriate interval before the subsequent
message
2.1.4.2
XG  System  Data  parameter  change
(ESBL Part)
See tables <1-1> and <1-2>.
2.1.4.3
Multi  Effect1  Data  parameter  change
(ESBL Part)
See tables <1-1> and <1-3>.
2.1.4.4
Multi  Part  Data  parameter  change
(ESBL Part)
See tables <1-1> and <1-4>.
2.1.4.5
Drums  Setup  Data  parameter  change
(ESBL Part)
See tables <1-1> and <1-5>.
If a Drum Setup Reset parameter change message is received,
the Drum Setup parameter values will be initialized.
Selecting a Drum Set will cause the Drum Setup parameter
values to be initialized.
4
2.1.5
Other  parameter  changes
2.1.5.1
Master  Tuning
(ESBL Part)
11110000
F0
01000011
43
0001nnnn
1n
00100111
27
00110000
30
00000000
00
00000000
00
0mmmmmmm
mm
0lllllll
ll
0ccccccc
cc
11110111
F7
This message simultaneously changes the pitch of all channels.
2.2
Bulk  Dump
(ESBL Part)
The Disklavier receives the following bulk dump data.
[XG NATIVE]
1) XG System Data
2) Multi Effect1 Data
3) Multi Part Data
4) Drums Setup Data
[QS300 NATIVE]
1) QS300 User Normal Voice Data
2.2.1
XG  Native  Bulk  Dump
11110000
F0
01000011
43
0000nnnn
0n
01001100
4C
0bbbbbbb
bbbbbbb
0bbbbbbb
bbbbbbb
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
0ddddddd
dd
|
|
|
|
0ccccccc
ccccccc
11110111
F7
For the Address and Byte Count, refer to the supplementary
tables.
The Checksum is the value that results in a value of 0 for the
lower 7 bits when the Start Address, Byte Count, plus the
Checksum itself are added.
2.2.1.1
XG  System  Data  bulk  dump
(ESBL Part)
See tables <1-1> and <1-2>.
2.2.1.2
Multi  Effect1  Data  bulk  dump
(ESBL Part)
See tables <1-1> and <1-3>.
2.2.1.3
Multi  Part  Data  bulk  dump
(ESBL Part)
See tables <1-1> and <1-4>.
2.2.1.4
Drums  Setup  Data  bulk  dump
(ESBL Part)
See tables <1-1> and <1-5>.
2.2.2
QS300  Native  Bulk  Dump
11110000
F0
01000011
43
0000nnnn
0n
01001101
4B
0bbbbbbb
bbbbbbb
0bbbbbbb
bbbbbbb
0aaaaaaa
aaaaaaa
0aaaaaaa
aaaaaaa
Exclusive status
YAMAHA ID
Device Number
Model ID
Sub ID2
Master Tune MSB
Master Tune LSB
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
XG Model ID
ByteCount
ByteCount
Address High
Address Mid
Address Low
Data
Checksum
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
QS300 Model ID
ByteCount
ByteCount
Address High
Address Mid

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Du1a

Table of Contents