RIDGID OF60150HA Operator's Manual page 11

OPERATION
 Make sure the air compressor is off and unplugged.
 Rotate pressure regulator knob fully in the counter-
clockwise direction so that the outlet pressure is at
zero (0) psi.
 Attach an air hose with 1/4 in. NPT quick-connect air fitting
to a quick connect coupler (1/4 in.) on air compressor.
Make sure to push the air fitting fully into the coupler until
the sleeve springs forward to lock in place.
To disconnect an air hose or an air tool:
 Confirm that the outlet pressure is at zero (0) psi.
 When disconnecting a hose from quick connect coupler
(1/4 in.), always firmly hold fitting end of hose.
 Push back on the release sleeve on the 1/4 in. quick-
connect coupler.
 With a firm grip, pull out the quick-connect air fitting that
is attached to the quick connect coupler.
BREAK-IN PERIOD
Before first use, run the air compressor at zero (0) tank pres-
sure with the drain valve fully open for 30 minutes.
TURNING THE AIR COMPRESSOR ON/OFF
See Figure 3, page 16.
 With the air compressor plugged in, place the on/off
switch in the ON ( l ) position to power the compressor
on.
 To turn the air compressor off, place the on/off switch in
the OFF ( O ) position.
NOTE: When the compressor is in the ON ( l ) position, the
air compressor will automatically turn back on when the
designated tank air pressure drops below the cut-in pressure.
It will shut off again when the cut-out pressure is reached.
WARNING:
Never exceed the air tool's pressure rating as
recommended by the manufacturer. When using
this air compressor as an inflation device, always
follow the maximum inflation guidelines stated by
the manufacturer of the item being inflated.
WARNING:
Always ensure the switch is in the OFF ( O ) position
and the regulator pressure gauge reads zero before
changing air tools or disconnecting the hose
from the air outlet. Failure to do so could result in
possible serious personal injury.
USING THE AIR COMPRESSOR
See Figure 4, page 17.
WARNING:
Risk of bursting. Do not adjust pressure regulator
knob to result in output pressure greater than
marked maximum pressure of attachment and/
or the item being inflated. Never use at pressure
greater than 150 psi. Failure to heed this warning
could result in possible serious personal injury.
WARNING:
Air powered tools may require more air consump-
tion than this air compressor is capable of provid-
ing. Check the tool manual to avoid damage to the
tool or risk of personal injury.
 Attach air hose following the instructions in Connecting/
Disconnecting Air Hose (Not Provided).
 Set the amount of air pressure desired using the pressure
regulator knob. Pull the knob out, then turn clockwise to
increase or counterclockwise to decrease the air pressure
to be provided through the hose. When the desired
pressure is set, push the knob back in to lock.
NOTE: Always use the minimum amount of pressure
necessary for your application. Using a higher pressure
than needed will drain air from the tank more rapidly and
cause the unit to cycle on more frequently.
 When finished, always drain the tank and unplug the
unit. Never leave the unit plugged in and/or running
unattended.
DRAINING THE TANK
See Figure 5 - 6, page 17.
To help prevent tank corrosion and keep moisture out of the air
used, the air tank of the compressor should be drained daily.
To drain:
 Turn the air compressor off and disconnect the plug from
the power supply,
 Pull the ring on the safety valve to release pressure until
pressure gauge reads less than 20 psi.
 Release the ring.
 Turn the drain valve 90° counterclockwise to the ON
(open) position.
 Tilt tank as shown to drain moisture from tank into a
suitable container.
NOTE: Condensate is a polluting material and should be
disposed of in compliance with local regulations.
 If drain valve is clogged, release all air pressure, remove
and clean valve, then reinstall.
11 – English