Specifications - Dremel 3000 Original Instructions Manual

e. When using rotary files, cut-off wheels, high-speed
cutters or tungsten carbide cutters, always have
the work securely clamped. These wheels will grab
if they become slightly canted in the groove, and can
kickback. When a cut-off wheel grabs, the wheel itself
usually breaks. When a rotary file, high-speed cutter
or tungsten carbide cutter grabs, it may jump from the
groove and you could lose control of the tool.
SAFETY WARNINGS SPECIFIC FOR GRINDING AND
ABRASIVE CUTTING-OFF OPERATIONS
a. Use only wheel types that are recommended
for your power tool and only for recommended
applications. For example: do not grind with the
side of a cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
b. For threaded abrasive cones and plugs use only
undamaged wheel mandrels with an unrelieved
shoulder flange that are of correct size and length.
Proper mandrels will reduce the possibility of breakage.
c. Do not "jam" a cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases the
loading and susceptibility to twisting or snagging of
the wheel in the cut and the possibility of kickback or
wheel breakage.
d. Do not position your hand in line with and behind
the rotating wheel. When the wheel, at the point of
operation, is moving away from your hand, the possible
kickback may propel the spinning wheel and the power
tool directly at you.
e. When wheel is pinched, snagged or when
interrupting a cut for any reason, switch off the
power tool and hold the power tool motionless until
the wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur.
Investigate and take corrective action to eliminate the
cause of wheel pinching or snagging.
f. Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind, walk
up or kickback if the power tool is restarted in the
workpiece.
g. Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
h. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress
the wires by applying excessive load to the brush.
The wire bristles can easily penetrate light clothing
and/or skin.
b. Allow brushes to run at operating speed for at least
one minute before using them. During this time no
one is to stand in front or in line with the brush.
Loose bristles or wires will be discharged during the
run-in time.
c. Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire fragments
may be discharged at high velocity during the use of
these brushes and may become imbedded in your skin.
d. Do not exceed 15,000 RPM when using wire brushes
DO NOT WORK WITH MATERIALS CONTAINING
!
ASBESTOS (asbestos is considered carcinogenic)
TAKE PROTECTIVE MEASURES WHEN DURING
!
WORK DUST CAN DEVELOP THAT IS HARMFUL TO
ONE'S HEALTH, COMBUSTIBLE OR EXPLOSIVE (some
dusts are considered carcinogenic); wear a dust mask
and work with dust/chip extraction when connectable

SPECIFICATIONS

Model number . . . . . . . . 3000
Input. . . . . . . . . . . . . . . . . 130 W
Voltage. . . . . . . . . . . . . . . 230 V, 50 Hz
Speed . . . . . . . . . . . . . . . 33,000/min
Collet capacity . . . . . . . . . 3.2 mm
Max. accessory ∅ . . . . . . 38.1 mm
Weight . . . . . . . . . . . . . . . 0.5 kg
Model number . . . . . . . . 4000
Input. . . . . . . . . . . . . . . . . 175 W
Voltage. . . . . . . . . . . . . . . 230-240 V, 50-60 Hz
Speed . . . . . . . . . . . . . . . 35,000/min
Collet capacity . . . . . . . . . 3.2 mm
Max. accessory ∅ . . . . . . 38.1 mm
Weight . . . . . . . . . . . . . . . 0.6 kg
Model number . . . . . . . . 4300
Input. . . . . . . . . . . . . . . . . 175 W
Voltage. . . . . . . . . . . . . . . 220-240 V, 50-60 Hz
Speed . . . . . . . . . . . . . . . 35,000/min
Collet capacity . . . . . . . . . 0.8-3.4 mm
Max. accessory ∅ . . . . . . 38.1 mm
Weight . . . . . . . . . . . . . . . 0.6 kg
Use completely unrolled and safe extension cords with
a capacity of 5 Amps.
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool.
GENERAL
A. Collet nut
B. Collet
C. Nose cap (EZ Twist integrated wrench*)
D. Shaft lock button
E. On/Off and variable speed slide switch (3000)
E. On/Off switch (4000/4300)
F. Hanger
G. Brush cover
H. Ventilation openings
I. Variable speed dial (4000/4300)
J. Collet wrench
K. Light module (4300)
L. Dremel chuck (4300)
*) not standard included
LIGHT MODULE
M. On/Off switch
N. Slider (I)
O. Screw
P. Battery compartment
Q. Batteries (2 x CR1025)
R. New style nose cap
S. Old style nose cap
19
7
I & II (4300)
8