INTRODUCTION The Cogeco Atlas DVR 5-Device Universal Remote Control by Universal Electronics is our latest generation universal remote control.Its sophisticated technology allows you to consolidate up to five of your original home entertainment remote controls into one easy-to-use product. Moreover, it’s packed with advanced features such as: •...
FEATURES AND FUNCTIONS Use the illustration below to locate features on the Cogeco Atlas DVR 5-Device Universal Remote Control and then study the Key Charts (on the next three pages) to learn how they function. To find out what type of devices can be controlled by each device key after programming, see the Device Table on page 8.
Key Charts Use SETUP for all programming sequences. Press PWR once to turn on or off a home entertainment device. For MASTER POWER control, see Using The Master Power Key on page 18. Press AUX, DVD, AUD, TV, or CBL once to select a home entertain- ment device to control.Also see the Device Table on page 8.
Page 6
FEATURES AND FUNCTIONS Key Charts (continued) Use VOL+ (or VOL-) to raise (or lower) the audio volume. Use FAV to cycle through your favorite channels stored in your digital cable receiver. Use CH+ (or CH-) to select the next higher (or lower) channel. For DVD players, use these keys to skip forward (or reverse) through chapters.
Page 7
In all modes except CBL, use REW, PLAY, FFWD, STOP, and PAUSE to control a VCR, DVD player, or a DVR (after selecting a desired device). To record in the VCR mode, press REC twice. In the CBL mode, use above keys to control DVR functions of the digital cable receiver.
FEATURES AND FUNCTIONS (continued) Device Table NOTE: Please refer to the table below when performing the instructions in “Programming Device Control” on page 10 or “Programming TV/ VCR Combo Control” on page 12. After programming, the Cogeco Atlas DVR 5-Device Universal Remote Control will be able to control the following types of devices: DEVICE KEY...
INSTALLING BATTERIES On the back of the remote control, push the tab and lift off the battery cover. Locate the two (2) enclosed AA batteries. Match the + and – marks with those in the battery case, then insert them. Align the cover’s keys with the case’s holes and press the cover back into place.
PROGRAMMING DEVICE CONTROL The Cogeco Atlas DVR 5-Device Universal Remote Control is preprogrammed to operate the Motorola digital cable receiver provided by your cable system, an RCA TV, a Toshiba DVD player, an RCA VCR (as an AUX device), and a Pioneer audio receiver.
Page 11
AUX Code Device Type:_______________________ DVD Code Device Type:_______________________ AUD Code Device Type:_______________________ CBL Code Device Type:_______________________ TV Code...
PROGRAMMING TV/VCR COMBO CONTROL If you own a TV/VCR Combo, perform the following instructions to control this device: Turn on your TV/VCR Combo and insert a video cassette. On the remote control, press AUX once; it will blink once. Then press and hold SETUP until the AUX key blinks twice, then release SETUP.
SEARCHING FOR YOUR CODE If your home entertainment device does not respond to the Cogeco Atlas DVR 5-Device Universal Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: Turn on your TV.
CHECKING THE CODES If you have set up the Cogeco Atlas DVR 5-Device Universal Remote Control using the Searching For Your Code proce- dure (on the previous page), you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV: On the remote control, press TV once;...
PROGRAMMING CHANNEL CONTROL LOCK By default,the Cogeco Atlas DVR 5-Device Universal Remote Control’s channel-control capabilities are unlocked. NOTE: This feature does not affect the AUD mode. To Activate Channel Control Lock: On the remote control, press CBL once; it will blink once.
PROGRAMMING THE F1 KEY FOR SPECIFIC CHANNELS The Cogeco Atlas DVR 5-Device Universal Remote Control includes a programmable F1 key (located directly below the LAST key). The F1 key can be programmed to remember five of your favorite cable channel settings. If you want to change the cable channels previously-programmed on the F1 key, you’ll need to clear the key first (see the next page).
To Clear The F1 Key: On the remote control, press CBL once; it will blink once. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. Enter 9 - 9 - 5. The CBL key will blink twice.
USING THE MASTER POWER KEY The Cogeco Atlas DVR 5-Device Universal Remote Control has a unique feature that allows you to sequentially turn on or off up to five of your home entertainment devices with a single key press. NOTE: MASTER POWER ( PWR ) only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off.
To Clear The Master Power Key: Perform steps 1 and 2 in the first section above, To Program The Master Power Key. To clear the settings and exit the program, press and hold SETUP until the CBL key blinks twice, then release SETUP. RE-ASSIGNING DEVICE KEYS The Cogeco Atlas DVR 5-Device Universal Remote Control can be set up to control a second device.
RE-ASSIGNING DEVICE KEYS (continued) To Re-Assign AUX as 2nd AUD key: AUX - SETUP - 9 - 9 - 2 - AUD - AUX AUX as 2nd TV key: AUX as 2nd CBL key: AUX - SETUP - 9 - 9 - 2 - CBL - AUX AUX back to AUX: To re-assign another unused device key, substitute it for the AUX key above and then perform the sequence.
Repeat steps 1 through 3 (of this section) for each device you want volume to be unlocked. Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-, or MUTE, will control the device’s volume only in its own mode.
TROUBLESHOOTING PROBLEM: Device key does not blink when you press a key. SOLUTION: Replace the batteries with two (2) new AA alkaline batteries (see page 9). PROBLEM: Device key blinks when you press a key, but home entertainment device does not respond. SOLUTION: Make sure you are aiming the remote control at your home entertainment device and that you are within 15 feet of the device you are trying...
For help via e-mail, contact us at: cablehelp@ueic.com Copyright 2004 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without prior written permission of Universal Electronics Inc.
INFORMATION PRÉLIMINAIRE L'Atlas ENP 5 APPAREILS de Cogeco, fabriquée par Universal Electronics, est notre plus récente télécommande universelle. Sa tech- nologie d’avant-garde vous permet de regrouper en une seule télécom- mande jusqu’à 5 télécommandes d’appareils faisant partie de votre sys- tème de divertissement.
CARACTÉRISTIQUES ET FONCTIONS L’illustration de l’Atlas ENP 5 APPAREILS de Cogeco ci-dessous vous permet de repérer les fonctions de cette télécommande universelle et de comprendre leur fonctionnement avec l’aide du Tableau des touches (trois prochaines pages). Pour connaître quels types d’appareils peuvent être contrôlés par cha- cune des touches, une fois celles-ci programmées, consultez le Tableau des appareils à...
Tableau des touches Utilisez la touche SETUP pour toutes les séquences de programmation. Appuyez sur la touche PWR une fois pour mettre en marche/arrêter un ou plusieurs appareils de votre système de divertisse- ment. Pour la fonction MASTER POWER, consultez la section Touche Master Power à...
Page 28
CARACTÉRISTIQUES ET FONCTIONS Tableau des touches (suite) Appuyez sur la touche A, B, ou C pour afficher des options de télé par câble additionnelles. Utilisez la touche VOL+ (ou VOL-) pour augmenter (ou réduire) le volume. Utilisez la touche FAV pour choisir parmi vos canaux préférés, mémorisés dans votre décodeur numérique.
Page 29
Pour tous les modes (sauf CBL), utilisez les touches REW, PLAY, FFWD, STOP et PAUSE pour commander un magnétoscope, un lecteur DVD ou un magnétoscope (après avoir préalablement choisi l’appareil). Pour enregistrer en mode magnétoscope (VCR), appuyez deux fois sur la touche REC. En mode CBL, utilisez ces touches pour commander les fonctions ENP du décodeur numérique.
CARACTÉRISTIQUES ET FONCTIONS (suite) Tableau des appareils VEUILLEZ NOTER : consultez le tableau ci-dessous lorsque vous effectuez le “Réglage de la télécommande en fonction des appareils” (page 32) ou le “Réglage de la fonction combinée Télé/Vidéo” (page 34). Une fois programmée, la télécommande universelle Atlas ENP 5 APPAREILS de Cogeco vous permettra de commander les types d’appareils suivants : TOUCHE...
INSTALLATION DES PILES Au dos de votre télécommande, retirez le couvercle des piles. Placez les deux piles AA (incluses) en faisant correspon- dre les marques + et – des piles avec celles du boîtier. Alignez les onglets de fermeture du couvercle des piles avec les trous du boîtier et remettez le couvercle en place en appliquant une légère pression.Vous entendrez un clic indiquant que le couvercle est correctement fermé.
RÉGLAGE DE LA TÉLÉCOMMANDE EN FONCTION DES APPAREILS La télécommande universelle Atlas ENP 5 APPAREILS de Cogeco est préprogrammée par défaut pour fonctionner avec le décodeur numérique de Motorola fourni par votre câblodistributeur, un téléviseur RCA, un lecteur DVD Toshiba, un magnétoscope RCA (en mode AUX) et un amplificateur audio/radio de marque Pioneer.
Page 33
Code AUX Type d’appareil : ___________________________ Code DVD Type d’appareil : ___________________________ Code AUD Type d’appareil : ___________________________ Code CBL Type d’appareil : ___________________________ Code TV...
RÉGLAGE DE LA FONCTION COMBINÉE TÉLÉ/VIDÉO Si vous possédez un appareil combiné Télé/Vidéo, suivez les instruc- tions de réglage suivantes : Allumez l’appareil et insérez une vidéocassette. Sur la télécommande, appuyez une fois sur la touche AUX. Le voyant lumineux clignotera alors une fois. Ensuite, appuyez sur la touche SETUP et tenez-la enfoncée jusqu’à...
COMMENT TROUVER LE CODE DE L’APPAREIL Si, après avoir essayé tous les codes listés pour votre appareil, celui-ci ne répond pas à la télécommande universelle Atlas ENP 5 APPAREILS de Cogeco ou si la marque de l’appareil n’est pas sur la liste, essayez de faire une recherche de code.
VÉRIFICATION DES CODES Si vous avez programmé votre télécommande universelle Atlas ENP 5 APPAREILS de Cogeco à l’aide de la procédure de recherche d’un code (section Comment trouver le code de l’appareil à la page précédente) et que vous désirez connaître le code à 4 chiffres. Si vous désirez connaître le code à...
RÉGLAGE DU VERROUILLAGE DU CONTRÔLE DES CANAUX Par défaut, les paramètres de contrôle des canaux de la télécommande ne sont pas verrouillés en fonction du décodeur numérique. VEUILLEZ NOTER : cette fonction n’affecte pas le mode Pour activer le verrouillage du contrôle des canaux : Sur la télécommande, appuyez une fois sur la touche CBL : le voyant lumineux clignotera une fois.
RÉGLAGE DE LA TOUCHE F1 POUR CANAUX SPÉCIFIQUES La télécommande universelle Atlas ENP 5 APPAREILS de Cogeco comporte une touche F1 programmable (située directement sous le touche LAST). Cette touche peut être programmée pour garder en mémoire cinq de vos chaînes préférées. Si vous désirez modifier les canaux préalablement programmés sur la touche F1, vous devrez d’abord procéder à...
Effacement de la touche F1 : Sur la télécommande, appuyez une fois sur la touche CBL; celle-ci clignotera alors une fois. Ensuite, appuyez sur la touche SETUP et tenez-la enfoncée jusqu’à ce que la touche CBL clignote deux fois. Relâchez ensuite la touche SETUP.
TOUCHE MASTER POWER La télécommande universelle Atlas ENP 5 APPAREILS de Cogeco est munie d’une touche de fonction unique qui vous permet d’allumer et d’éteindre, de façon séquentielle, jusqu’à cinq appareils faisant partie de votre système de divertissement, simplement en appuyant sur une seule touche.
Effacement de la touche Master Power : Effectuez les étapes 1 et 2 de la section précédente Réglage de la touche Master Power. Pour sauvegarder et quitter la fonction de réglage de la séquence, appuyez sur la touche SETUP et tenez-la enfoncée jusqu’à...
MODIFICATION DE LA FONCTION DES TOUCHES (suite) Pour programmer la touche AUX en tant que 2e touche AUD : AUX en tant que 2e touche TV : AUX en tant que 2e touche CBL : AUX à nouveau en tant que touche AUX : Pour attribuer une nouvelle fonction à...
Entrez le numéro 9 - 9 - 3 : la dernière touche de mode choisie clignotera deux fois. Sélectionnez le mode (ex. : TV) pour lequel vous voulez que le réglage du volume soit verrouillé de façon générale. La touche de mode choisie clignotera deux fois. Par la suite, vous serez en mesure de commander le volume de l’appareil choisi (ex.
DÉPANNAGE PROBLÈME : La touche de mode ne clignote pas quand vous appuyez sur une touche. SOLUTION : Remplacez les piles par 2 nouvelles piles alcalines de type AA (page 31). PROBLÈME : La touche de mode clignote lorsque vous appuyez sur une touche mais l’appareil ne répond pas à...
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For Audio Amplifiers: Codes de configuration pour les amplifica- teurs audio : Accuphase Acurus Adcom Aiwa AudioSource Biamp Bose Carver Classe Curtis Mathes Denon Digital Audio Control Durabrand Elan Forte GoldStar Harman/Kardon Kenwood Left Coast Lenoxx Linn...
Victor Wards Yamaha Setup Codes For Audio Receivers: Codes de configuration pour les récepteurs audio : Adcom Aiwa Akai Alco Amphion Media Works Anam Apex Digital Arcam Audiotronic Audiovox Bose Cambridge Soundworks Capetronic Carver Casio Clarinette Classic Coby Compaq Criterion Curtis Mathes Daewoo Dell...
Page 48
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For Audio Receivers, continued: Codes de configuration pour les récepteurs audio, suite : Kenwood Koss Lasonic Lenoxx Lexicon Linn Liquid Video Lloyd’s Magnavox Marantz Mitsubishi Modulaire Nakamichi Norcent Onkyo Optimus Oritron Panasonic Penney Philco Philips Pioneer...
Sharp Sharper Image Sherwood Shinsonic Sonic Blue Sony Soundesign Stereophonics Sunfire Teac Technics Thorens Venturer Victor Wards Yamaha Yorx Zenith Setup Codes For Cable Boxes Converters: Codes de configuration pour les décodeurs : Americast Bell & Howell Bell South Clearmaster ClearMax Coolmax Digi...
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For Cable Boxes, continued: Codes de configuration pour les décodeurs, suite : Runco Samsung Scientific Atlanta Sony Starcom Supercable Supermax Tocom Torx Toshiba Tristar Viewmaster Vision Vortex View Zenith Setup Codes For DVD Players: Codes de configuration pour les lecteurs DVD : Adcom Advent...
Page 51
CyberHome Daewoo Denon Dual DVD2000 Emerson Enterprise Fisher Funai Gateway Go Video Greenhill Harman/Kardon Hitachi Hiteker Initial Integra Jamo Jaton Jensen jWin Kenwood Konka Koss Landel Lasonic Lenoxx Liquid Video Lite-On Loewe Magnavox Malata Marantz Memorex Microsoft Mintek Mitsubishi Momitsu Nesa Next Base Norcent...
Page 52
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For DVD Players, continued: Codes de configuration pour les lecteurs DVD, suite : Panasonic Philco Philips Pioneer Polaroid Polk Audio Portland Prima Princeton Proscan ProVision Qwestar Regent Rotel Rowa Saba Sampo Samsung Sansui Sanyo Sharp Sharper Image...
US Logic V Inc. Vocopro Xbox Xwave Yamaha Zenith Setup Codes For PVRs: Codes de configuration pour les ENP : Alienware CyberPower Dell Gateway Hauppauge Hewlett Packard Howard Computers iBUYPOWER Media Center PC Microsoft Mind Northgate Panasonic Philips ReplayTV Sonic Blue Sony Systemax Tagar Systems...
MANUFACTURER’S CODES, continued CODES DES MANUFACTURIERS, suite Setup Codes For TVs: Codes de configuration pour les téléviseurs : A-Mark Abex Admiral Advent Adventura Aiko Aiwa Akai Alaron Albatron Ambassador America Action Ampro Anam Anam National Apex Digital Archer Audiovox Axion Belcor Bell &...
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For TVs, continued: Codes de configuration pour les téléviseurs, suite : Thomas TNCi Toshiba Tosonic Totevision Trical Universal V Inc. Vector Research Victor Vidikron Vidtech Viewsonic Viking Wards Waycon White Westinghouse Yamaha Zenith Zonda Setup Codes For TV/VCR Combos: Codes de configuration pour les combinés...
Magnin Memorex Mitsubishi Optimus Orion Panasonic Penney Quasar Sansui Sanyo Sears Sharp Sony Sylvania Symphonic Thomas White Westinghouse Zenith Setup Codes For VCRs: Codes de configuration pour les magnétoscopes : Admiral Adventura Aiko Aiwa Akai Alienware America Action American High Asha Audiovox Beaumark...
Page 60
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For VCRs, continued: Codes de configuration pour les magnétoscopes, suite : Curtis Mathes Cybernex CyberPower Daewoo Daytron Dell Denon DirecTV Dish Network System Dishpro Durabrand Dynatech Echostar Electrohome Electrophonic Emerex Emerson Euro Expressvu Fisher Fuji Funai...
Page 61
Kenwood Kodak Lloyd’s Logik Magnasonic Magnavox Magnin Marantz Marta Matsushita Media Center PC Memorex MGN Technology Microsoft Mind Minolta Mitsubishi Motorola Multitech Nikko Noblex Northgate Olympus Onkyo Optimus Orion Panarex Panasonic Pansat Penney Pentax Philco Philips Pilot Pioneer Polk Audio Portland Profitronic Proscan...
Page 62
MANUFACTURER’S CODES CODES DES MANUFACTURIERS Setup Codes For VCRs, continued: Codes de configuration pour les magnétoscopes, suite : Protec Pulsar Quarter Quartz Quasar RadioShack Radix Randex Realistic ReplayTV Runco Samsung Sanky Sansui Sanyo Scott Sears Sharp Shogun Singer Sonic Blue Sony Sylvania Symphonic...