Advertisement
Quick Links
John Lewis
Thank you for purchasing this Rouen Storage Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
Do not use power tools to assemble.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email mail@fwgroup-uk.com
Rouen Storage Bed
y.
1/10
For product support or spare parts please call
the John Lewis Helpline;
E: mail@fwgroup-uk.com
King, Superking
T: 01244 689949
Advertisement
Related Manuals for John Lewis Rouen
Summary of Contents for John Lewis Rouen
- Page 1 John Lewis Rouen Storage Bed King, Superking Thank you for purchasing this Rouen Storage Bed. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. For product support or spare parts please call the John Lewis Helpline;...
- Page 2 Fittings and parts checklist Fittings M6 x 25mm Bolt x 6 pcs M4 Allen Key x 1 pcs M5 Allen Key x 1 pcs M6 x 40mm Bolt x 8 pcs Centre Caps x 8 pcs Screw 4 x 50mm x 4pcs Side Caps x 16 pcs Screw 3.5 x 30mm x 42pcs Wide Centre Caps x 8...
- Page 3 Parts Headboard x 1 Footboard x 1 Side Rails x 2 Slats x 16 Wide Slats x 16 Centre Rail x 1 Wooden Legs x 4 Drawer Runner Base x 2 Drawer Centre Support x 1 Drawer Sides x 4 Drawer Fronts x 2 Drawer Backs x 2 Drawer Bottoms x 2...
- Page 4 Step One Place metal bracket on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2) and hand-tighten to loosely secure parts together. Do not tighten bolts with M5 Allen Key (B) until you have inserted the Centre Rail in Step Four.
- Page 5 Step Three Attach Drawer Centre Support (9) to Drawer Runner Base (8) and secure into place using Screws 4 x 50mm (K) as shown in the diagram below. Screw 4 x 50mm (K) Screw 4 x 50mm (K) Screw Cross head Screw Driver 4 x 50mm x 4 Step Four...
- Page 6 Step Five Insert the Front Legs (7)x2 into the pre-drilled holes on the underside of the Headboard (1) and twist to secure, as shown in the diagram below. Legs x 2 Step Six Attach the Metal Plate (16) to the bottom of the Footboard (2) using Bolts M6 X 25mm (I) x2. Do not tighten the bolts until you make adjustment for the screw hole at the Side Rail (3).
- Page 7 Step Seven To construct the drawers, fix Drawer Front (11) with one end of each Drawer Bottom Support (15) using Screws 3.5 x 30mm (L) as shown in Fig.1, then fix the Drawer Sides (10) to the Drawer Front (11). Next, insert Drawer Bottom (13) and then fix Drawer Back (12) using Screws 3.5 x 30mm (L) as shown in Fig.2.
- Page 8 Step Nine Attach Metal Stopper (16) to the Drawer Runner Base (8) using Screw 4 x 18mm (O). Screw 4 x 18 Metal Stopper x 4 8/10...
- Page 9 Step Ten With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either end(x16). (Please note the Wide Slats (5) must be inserted with the Wide Centre Caps (E) and Wide Side Caps (F)).
-
Page 10: Care And Maintenance
Care and Maintenance This Rouen Storage Bed should be cleaned using a soft damp cloth and dried immediately. Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently damage the surface.