Related Manuals for Neilsen CT1406
Summary of Contents for Neilsen CT1406
- Page 1 AIR BODY SAW CT1406 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 3: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: AIR BODY SAW Model: CT1406 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 11148-12 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Wear hearing protection. Wear safety goggles. - Page 5 Personal Safety 1. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of injury to persons. 2.
-
Page 6: Air Source
starting the tool unintentionally. Turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position before leaving the work area. 6. Store the tool when it is idle out of reach of children and other untrained persons. A tool is dangerous in the hands of untrained users. -
Page 7: Specifications
SPECIFICATIONS Max. operating pressure: 6.0 bar Max. speed: 8500/min Avg. air consumption: 4 cfm Hose size: 3/ 8" Air inlet: 1/ 4" Steel cutting capacity: up to 16 gauge COMPONENTS AND CONTROLS INITIAL SETUP & ASSEMBLY Air Supply WARNING: To prevent serious injury from explosion, use only clean, dry, regulated, compressed air to power this tool. - Page 8 2. Attach an air hose to the compressor s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and quick coupler, will make operation more efficient, but are not required. WARNING: To prevent serious injury from accidental operation, do not install a female quick coupler on the tool.
- Page 9 OPERATING INSTRUCTIONS Tool Set Up WARNING! TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the Trigger before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual.
- Page 10 Work Piece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage.
-
Page 11: User Maintenance Instructions
USER‑MAINTENANCE INSTRUCTIONS Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle before performing any inspection, maintenance, or cleaning procedures. -
Page 12: Troubleshooting
TROUBLESHOOTING Problem Possible Causes Likely Solutions Decreased output. 1. Not enough air pressure and/ 1. Check for loose connections and make sure that or air flow. air supply is providing enough air flow (CFM) 2. Obstructed Throttle. at required pressure (PSI) to the tool's air inlet. 3. -
Page 13: Assembly Diagram And Parts List
ASSEMBLY DIAGRAM AND PARTS LIST... - Page 16 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...