Installation; Contents; Trunk Mounting; Passenger Compartment Mounting - Rockford Fosgate PRIME R2-200X2 Installation & Operation Manual

Installation

Contents

• Prime Amplifier
• Mounting Hardware
• Allen Wrench
• Remote Level Control
(only available on
amplifiers with mono
channels)
Installation Considerations
• Fuse-holder and fuse.
(See specifications for
fuse rating)
• Volt/Ohm Meter
• Wire strippers
• Wire crimpers
• Wire cutters
• #2 Phillips screwdriver
• Battery post wrench
The following is a list of tools needed for installation:
This section focuses on some of the vehicle considerations for
installing your new amplifier. Pre-planning your system layout and
best wiring routes will save installation time. When deciding on the
layout of your new system, be sure that each component will be
easily accessible for making adjustments.
damage to the unit, fire and/or possible injury.
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before
attempting to install the unit.
2. For easier assembly, we suggest you run all wires prior to
mounting your unit in place.
3. Route all of the RCA cables close together and away from any
high current wires.
4. Use high quality Rockford Fosgate connectors for a reliable
installation and to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks,
fuel lines, brake, hydraulic lines, vacuum lines or electrical wiring
8
• 4-pin Molex pig tail
connectors
• Installation & Operation
Manual
• Hand held drill w/
assorted bits
• Assorted connectors
• Adequate Length &
gauge—Red Power Wire
• Adequate Length—
Remote Turn-on Wire (not
needed if using Auto Turn
ON feature)
• Adequate Length &
gauge—Black Grounding
Wire
If you feel unsure about installing this
system yourself, have it installed by a
qualified technician.
Before installation, disconnect the
battery negative (-) terminal to prevent
when working on any vehicle.
6. Never run wires underneath the vehicle. Running the wires
inside the vehicle provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber
or plastic grommets to protect any wires routed through metal,
especially the fire wall.
8. ALWAYS protect the battery and electrical system from damage
with proper fusing. Install the appropriate fuse holder and fuse
on the +12V power wire within 18" (45.7 cm) of the battery
terminal.
9. When grounding to the chassis of the vehicle, scrape
all paint from the metal to ensure a good, clean ground
connection. Grounding connections should be as short
as possible and always be connected to metal that is
welded to the main body, or chassis of the vehicle. Seat
belt bolts should never be used for connecting to ground.
Mounting Locations
To ensure optimal performance, mount the amplifier with at least
1" (25.4mm) of air gap around the amplifier's heat sink to provide
proper cooling.

Trunk Mounting

Mounting the amplifier vertically or inverted will provide adequate
cooling of the amplifier. Mounting the amplifier on the floor of the
trunk will provide the best cooling of the amplifier.

Passenger Compartment Mounting

Mounting the amplifier in the passenger compartment will work as
long as you provide a sufficient amount of air for the amplifier to cool
itself. If you are going to mount the amplifier under the seat of the
vehicle, you must have at least 1" (25.4mm) of air gap around the
engine compartment will void your warranty.
Battery and Charging
Amplifiers will put an increased load on the vehicle's battery and
charging system. We recommend checking your alternator and
battery condition to ensure that the electrical system has enough
capacity to handle the increased load of your stereo system. Stock
electrical systems which are in good condition should be able to
handle the extra load of any Prime Series amplifier without problems,
although battery and alternator life can be reduced slightly. To
maximize the performance of your amplifier, we suggest the use of a
heavy duty battery and an energy storage capacitor.
RLC Mounting Options – Utilize the included screws to secure the RLC
to the vehicle.
amplifier's heat sink.
Never mount this unit in the engine
compartment. Mounting the unit in the