Table of Contents
Advertisement
Installation
Contents
• M2 Element Ready™
Amplifier
• Mounting Hardware
• Allen Wrench
• Remote Level Control
(only available on
amplifiers with mono
channels)
Installation Considerations
• Fuse-holder and fuse.
(See specifications for
fuse rating)
• Volt/Ohm Meter
• Wire strippers
• Wire crimpers
• Wire cutters
• #2 Phillips screwdriver
• Battery post wrench
This section focuses on some of the vehicle considerations for
installing your new amplifier. Pre-planning your system layout and
best wiring routes will save installation time. When deciding on the
layout of your new system, be sure that each component will be
easily accessible for making adjustments.
If you feel unsure about installing this system yourself, have it
installed by a qualified technician.
1. Be sure to carefully read and understand the instructions before
attempting to install the unit.
2. For easier assembly, we suggest you run all wires prior to
mounting your unit in place.
3. Route all of the RCA cables close together and away from any
high current wires.
4. Use high quality Rockford Fosgate connectors for a reliable
installation and to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks,
fuel lines, brake, hydraulic lines, vacuum lines or electrical wiring
8
• 4-pin Molex pig tail
connectors
• Test tones available for download
at https://rftech.custhelp.com/
app/answers/detail/a_id/1126/
Scroll to the bottom of the page
and download your preferred
format.
• Hand held drill w/
assorted bits
• Assorted connectors
• Adequate Length &
gauge—Red Power Wire
• Adequate Length—
Remote Turn-on Wire (not
needed if using Auto Turn
ON feature)
• Adequate Length &
gauge—Black Grounding
Wire
Before installation, disconnect the
battery negative (-) terminal to prevent
damage to the unit, fire and/or possible
injury.
Before beginning any installation, follow
these simple rules:
when working on any vehicle.
6. Never run wires underneath the vehicle. Running the wires
inside the vehicle provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber
or plastic grommets to protect any wires routed through metal,
especially the fire wall.
8. ALWAYS protect the battery and electrical system from damage
with proper fusing. Install the appropriate fuse holder and fuse
on the +12V power wire within 18" (45.7 cm) of the battery
terminal.
9. When grounding to the chassis of the vehicle, scrape
all paint from the metal to ensure a good, clean ground
connection. Grounding connections should be as short
as possible and always be connected to metal that is
welded to the main body, or chassis of the vehicle. Seat
belt bolts should never be used for connecting to ground.
Mounting Locations
To ensure optimal performance, mount the amplifier with at least
1" (25.4mm) of air gap around the amplifier's heat sink to provide
proper cooling.
Trunk Mounting
Mounting the amplifier vertically or inverted will provide adequate
cooling of the amplifier. Mounting the amplifier on the floor of the
trunk will provide the best cooling of the amplifier.
Passenger Compartment Mounting
Mounting the amplifier in the passenger compartment will work as
long as you provide a sufficient amount of air for the amplifier to cool
itself. If you are going to mount the amplifier under the seat of the
vehicle, you must have at least 1" (25.4mm) of air gap around the
amplifier's heat sink.
Battery and Charging
Amplifiers will put an increased load on the vehicle's battery and
charging system. We recommend checking your alternator and
battery condition to ensure that the electrical system has enough
capacity to handle the increased load of your stereo system. Stock
electrical systems which are in good condition should be able to
handle the extra load of any Prime Series amplifier without problems,
although battery and alternator life can be reduced slightly. To
maximize the performance of your amplifier, we suggest the use of a
heavy duty battery and an energy storage capacitor.
Never mount this unit in the engine
compartment. Mounting the unit in
the engine compartment will void your
warranty.
Advertisement
Table of Contents
