Panasonic KX-NS500AG Service Manual page 105

Pin No Pin Name
M3 DHW_DSP1
M4 UHW_DSP1
M5 NRST_EXT_O[0]
M6 FSYNC[9]
M7 LED_O[1]
M8 LED_O[3]
M9 VCCINT
M10 GND
M11 GND
M12 GND
M13 GND
M14 VCCINT
M15 VCCINT
M16 UHW_BASE[4]
M17 MSEL0
M18 FPGA_DONE
M19 UHW_BASE[3]
M20 UHW_BASE[2]
M21 UHW_BASE[1]
M22 UHW_BASE[0]
N1 NRST_EXT_O[3]
N2 NRST_EXT_O[2]
N3 GND
N4 VCC(IO)
N5 SHUT_STT_I
N6 LED_O[0]
N7 GPIO0[0]
N8 LED_O[0]
N9 VCCINT
N10 GND
N11 GND
N12 GND
N13 GND
N14 VCCINT
N15 GND
N16 HW_CLK[4]
N17 FSYNC[5]
N18 FSYNC[6]
N19 FSYNC[4]
N20 FSYNC[3]
N21 NC
N22 NC
P1 nOE_RST
P2 nRST_RMT
P3 NIRQ_O[0]
P4 NIRQ_O[2]
P5 NC
P6 NC
P7 NC
P8 GND
P9 VCCINT
P10 VCCINT
P11 VCCINT
P12 VCCINT
P13 VCCINT
P14 VCCINT
P15 NIRQ_EXT_I[0]
P16 nOE_ABUS
P17 nOE_DBUS
P18 VCC(IO)
P19 GND
P20 FSYNC[0]
P21 FSYNC[2]
P22 FSYNC[1]
R1 NC
R2 NIRQ_EXT_I[2]
R3 GND
I/O Function
O DSP#1 DOWN High Way
I DSP#1 UP High Way
O BASE CARD reset
O frame sync output
O LED(STATUS RED)
O LED(MASTER RED)
- VCC
- GND
- GND
- GND
- GND
- VCC
- VCC
I UP High Way from BASE card
I configuration mode select
O configuration DONE signal
I UP High Way from BASE card
I UP High Way from BASE card
I UP High Way from BASE card
I UP High Way from BASE card
O PHY reset
O DSP card reset
- GND
- VCC
I LED shutdown mode indicator
O LED(STATUS GREEN)
I/O SERIAL DTR
O LED(MASTER GREEN)
- VCC
- GND
- GND
- GND
- GND
- VCC
- GND
O High Way clock output
O frame sync output
O frame sync output
O frame sync output
O frame sync output
- No Connection
- No Connection
O reset buffer output enable
O RMT reset
O INT(FPGA#0)
O INT(DSP_CARD)
- No Connection
- No Connection
- No Connection
- GND
- VCC
- VCC
- VCC
- VCC
- VCC
- VCC
I IRQ from BASE card
O CPU address bus output enable
O CPU data bus output enable
- VCC
- GND
O frame sync output
O frame sync output
O frame sync output
- No Connection
I IRQ from BASE card
- GND
105
KX-NS500AG