Related Manuals for Electrolux Silent Performer Cyclonic EL4021A
Summary of Contents for Electrolux Silent Performer Cyclonic EL4021A
- Page 1 SERVICE MANUAL VACUUM CLEANER Number of E.H.P. Floor Care Silent Performer Cyclonic publication Factory: Edition: 2015 Publication number Rev. 01 09/2015 PR - 1/17...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General description ............................ 3 Exploded view ............................3 ACCESSIBILITY ............................5 Electronic Control ............................. 13 Motor power regulation ........................13 Electronic layout ..…………………………………………………………………………………………….15 Trouble shooting ............................16 Publication number Rev. 01 09/2015 PR - 2/17... -
Page 3: General Description
1 General description * Accessories may vary from model to model. 1.1 Exploded view Publication number Rev. 01 09/2015 PR - 3/17... - Page 4 Denomination Position MOTOR SUSPENSION RING 130B SUSPENSION PIN 130A LID MOTOR 990C MOTOR HOUSING 300A FILTER SEALING 120D CORD WINDER 335A LID MOTOR HOUSING 300B 014C POWER REGULATOR 500A HYGIENE FILTER LOWER PART WITH WHEELS HOLDER FRONT WHEEL 119B FRONTWHEEL 335B REARWHEEL 119A...
-
Page 5: Accessibility
ACCESSIBILITY The following chapter follows a disassembling process that step by step will allow the Technician to completely dismount the vacuum cleaner. Tags have been added to help finding quickly the needed item to be removed quickly. ATTENTION: Boards and electronic devices could be damaged by electrostatic discharges. Don’t touch any components without any ESD protection. - Page 6 Now you can take out the CW pedal easily. Remove two screw from the CW pedal nest. To remove the top cover need to click out the snappers at the following places: Publication number Rev. 01 09/2015 PR - 6/17...
- Page 7 Now you can remove the lid easily. To remove the left side top cover click out the snappers at the following places: Now its easy to remove the lid by hand. Publication number Rev. 01 09/2015 PR - 7/17...
- Page 8 Remove the 4 screw from the cyclone unit. Than take out the cyclone unit and the air channel. Remove the screw from the rear side. Publication number Rev. 01 09/2015 PR - 8/17...
- Page 9 Pull the regilation button to the minimum position. Click out the side cover fixing ribs trough the service holes on the bottom part. Remove the right side cover. Publication number Rev. 01 09/2015 PR - 9/17...
- Page 10 Click out the left side cover fixing ribs trough the service holes on the bottom part. Then remove the left side cover. Remove the screws from the front lid. Click out the snappers at both side. Rotate the hose connection ring clockwise. Publication number Rev.
- Page 11 Now remove the front lid and hose connection ring from the appliance. Take out the motor house from the bottom plate. Remove the Hepa filter frame from the back side. Remove the screws from the motor house lid. Publication number Rev.
- Page 12 Remove the motor house lid. Pull out the suspension ring from the motor house. Now you can reach the motor. Publication number Rev. 01 09/2015 PR - 12/17...
-
Page 13: Electronic Control
3 Electronic Control 3.1 Motor power regulation 1. Main plug connected: - Motor shall be off. 2. First start (after main plug is connected): - Motor power starts in Max power position (remote version). 3. Power setting is changed by regulation button: - Motor power steps up or down. - Page 14 Reset If the receiver has saved transmitter address – New transmitter / New bentend 1. Plug in the cord to the main. Do not turn on. 2. Send Reset signal - 1+4 button combination at the same time (to do this you have 20s after connection to main ) ) If the cleaner received the right reset signal it will fluctuate.
-
Page 15: Electronic Layout
Electronic layout Angerona L1 model: Angerona L2 model: ATTENTION: Boards and electronic devices could be damaged by electrostatic discharges. Don’t touch any components without any ESD protection. Publication number Rev. 01 09/2015 PR - 15/17... -
Page 16: Trouble Shooting
4 TROUBLE SHOOTING Problem Checks Cleaner without remote: Investigate if the plastic knob reaches the ON/OFF switch on the PCB. Replace the control unit (display PCB) Cleaner with radio remote: Investigate if both ON/OFF (cleaner and remote) is not working. If remote ON/OFF working, but not cleaner ON/OFF: Investigate if the plastic knob reaches the ON/OFF switch on the PCB. - Page 17 Publication number Rev. 01 09/2015 PR - 17/17...