Displaying Information [Status Display]; Using The Menus; How To Use The Menus - Toshiba TDP-D1 Owner's Manual

Using handy features (Continued)
I Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the button twice (or press the CALL button on the remote
control once).
When the button is pressed once, the Setting
display menu appears. Pressing it again displays
information p.27 . The table below shows what kind
of information is displayed. Press the button (or the
CALL button on the remote control) again to
dismiss the display.
Item Description
Input Input source name
RGB signal mode RGB input mode
H-resolution Horizontal resolution (in bits)
V-resolution Vertical resolution (in bits)
H-frequency Horizontal sync frequency
V-frequency Vertical sync frequency
Sync Sync signal polarity
Signal format Y/P /P signal format
B R
Video mode Color method of video signal
Lamp time Time of lamp use
Version Firmware version
Notes
1: The mode of supported RGB signals
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 1,500
hours, consult with a store about getting a replacement lamp (for TDP-D1: TDPLD1 and for
TDP-D2: TDPLD2) (sold separately) prepared.
5: [Version] shows the version of the projector's internal control program. This version is
referred to for customer service, etc.
Notes
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
• Conducting another operation while information is being displayed dismisses the
display.
Remote
Control panel Control
ON LAMP TEMP FAN
ON/STANDBY
ON/STANDBY INPUT
MUTE
AUTO
KEYSTONE
MENU
PAGE
DOWN
- +
VOL. VOL.
AUTO KEYSTONE AUTO SET
"Yes": displayed, "No": not displayed
Computer Y/P /P Video
B R
Yes Yes Yes
[Note 1] Yes No No
Yes No No
Yes No No
Yes No No
[Note 2]
Yes No No
[Note 3] Yes No No
No Yes No
No No Yes
[Note 4] Yes Yes Yes
[Note 5]
Yes Yes Yes
p.36 is shown.
26

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings,
using the operation buttons
I How to use the menus
The menu shown below is only for operation instructions and might be different from
the actual display.
LASER
CALL
FREEZE
2. Select a Category
AUTO
SET
PAGE
UP
Select a category by using
There are following three
categorys.
Image adjustment menu
Default setting menu
S-video
Yes
Display setting menu
No
No
No
No
3. Adjustments & Settings
No
No
Adjustment/Setting Value
No
Yes
Yes
Yes
These marks signify the
items can be adjusted/set
by using
These marks signify an
item can be switched by
using
The figure shows a typical example.
As the display may differ depending
on the item, use the following pages
as a reference.
These marks signify the items can be selected from
the list by using
After an item selected, apply it by pressing
4. Back
Note
• Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the main power switch is turned off before this, or the power goes
out, then the data will not be saved.
p.14 on the control panel (main unit side) and remote control.
1. Start
Display the Setting display menu
.
p.28
p.28
p.29
Press to open the menu
of the selected category.
Item
This mark signfy that
.
there are options.
Press to display a
list of options.
.
.
.
27
Displays the current
adjustments of selected
category.
Item shown with gray
cannot be adjusted for the
current input source.
5. To Finish
Finish via the Status
display menu.
To Status display
p.26
6. End
The menu disappears