Page 1 PORTÉGÉ M400 TOSHIBA PORTÉGÉ M400 Portable Personal Computer User’s Manual...
Page 2 Photo CD is a trademark of Eastman Kodak. Sonic RecordNow! is a registered trademark of Sonic Solutions. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. i.LINK is trademark and registered trademark of Sony Corporation.
Page 3: Fcc Information
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, IEEE1394...
Page 4 User’s Manual EU Declaration of Conformity TOSHIBA declares, that the product: PPM40* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
Page 5: Region Selection
User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04...
Page 6 User’s Manual One of the labels is located on the module. Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem ■...
Page 7: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 8 User’s Manual Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Page 9 User’s Manual Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Page 10 User’s Manual ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and b/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the...
Page 11: General Conditions
User’s Manual ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
Page 12 User’s Manual Description on Laser specification The optical drive such as DVD-ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE...
Page 13: Table Of Contents
PORTÉGÉ M400 Table of Contents Preface Manual contents ......... . xxi Conventions.
Page 14 Table of Contents USB floppy disk drive........2-14 Optical media drives.
Page 15 Changing the screen orientation ......4-10 Method 1: Changing the screen orientation using TOSHIBA Accelerometer Utilities and TOSHIBA Rotation Utility ... 4-11 Method 2: Changing the screen orientation using Cross Function Button .
Page 16 TOSHIBA Mic Effect ........4-40...
Page 17 Replacing the battery pack....... . . 6-13 TOSHIBA Password Utility ....... . . 6-15 User Password .
Page 18 Disconnecting ......... 8-23 TOSHIBA Express Port Replicator ......8-23 Security lock .
Page 19 TOSHIBA support ........
Page 20: Appendix B Display Controller And Modes
Appendix C AT Commands Appendix D S-registers Appendix E V.90 Appendix F Wireless LAN Appendix G TOSHIBA RAID Appendix H Bluetooth wireless technology Interoperability Appendix I AC Power Cord and Connectors Appendix J TOSHIBA Anti-theft Protection Timer Glossary Index User’s Manual...
Page 21: Manual Contents
PORTÉGÉ M400 Preface Congratulations on your purchase of the PORTÉGÉ M400 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M400 computer.
Page 22: Conventions
Preface Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, Setup, explains how to configure the computer using the HW Setup program and TPM.
Page 23: Key Operation
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 24 Preface xxiv User’s Manual...
Page 25: General Precautions
PORTÉGÉ M400 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 26: Pc Card Overheating
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system.
Page 27: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 28: Software
■ TOSHIBA Mic Effect ■ TOSHIBA Password Utility ■ TOSHIBA Rotation Utility ■ TOSHIBA Accelerometer Utilities ■ TOSHIBA Tablet Access Code Logon Utility ■ Fingerprint utility ■ TOSHIBA Wireless Key Logon ■ Online manual Documentation ■ PORTÉGÉ M400 Portable Personal Computer User's Manual ■...
Page 29: Features
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with one of the ®...
Page 30 Introduction Legal Footnote (Memory (Main System)) For more information on the Legal Footnote regarding Memory (Main System), please refer to the Legal Footnotes section in Chapter 10. Click the *2. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack.
Page 31 Introduction Legal Footnote (HDD Drive Capacity) For more information on the Legal Footnote regarding HDD Drive Capacity, please refer to the Legal Footnotes section in Chapter 10. Click the *4. Optical media drive Computers in this series can be configured with an optical media drive installed in the Ultra Slim Bay.
Page 32 Introduction DVD Super Multi Some models are equipped with a full-size DVD drive Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
Page 33: Pointing Device
Introduction Legal Footnote (LCD) For more information on the Legal Footnote regarding LCD, please refer to the Legal Footnotes section in Chapter 10. Click the *5. Graphics controller The graphics controller maximizes display performance. Refer to Display Controller and Modes section in Appendix B for more information.
Page 34: Appendix E
Introduction Docking This port enables connection of an optional TOSHIBA Express Port Replicator described in Options section. i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras. Slots PC card The PC card slot accommodates a Type II card.
Page 35 Introduction Bluetooth Some computers in this series are equipped with Bluetooth functions. Bluetooth wireless technology eliminates the need for cables between electronic devices such as computers and printers. Bluetooth provides fast, reliable, and secure wireless communication in a small space. Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other...
Page 36: Special Features
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Cross Function Press this button more than a second to show the button menu screen.
Page 37 You can specify the time and select either the System Standby or System Hibernation item of the Basic Setup tab in TOSHIBA Power Saver. Keypad overlay A ten-key pad is integrated into the keyboard.
Page 38 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Actions tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...
Page 39: Utilities
Buttons: Assign applications or functions to the TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). User’s Manual 1-13...
Page 40 “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD- Video.
Page 41 Extension open the property dialog, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
Page 42 TOSHIBA Mic Effect TOSHIBA Mic Effect provides you the Echo Canceller and the Microphone Array functions. For more instructions for this software, click start, point to All Programs, point to TOSHIBA, point to Utilities and click TOSHIBA Mic Effect Help. TOSHIBA RAID TOSHIBA RAID Utility is used to create or manage RAID array.
Page 43 You can boot TOSHIBA Accelerometer Utilities from the menu bar as follows. Click start, click All Programs, click TOSHIBA, click Tablet PC and Setup for TOSHIBA Accelerometer Utilities. The Setting of TOSHIBA Accelerometer Utilities screen appears.
Page 44: Options
AC adaptor for each site so you will not have to carry the adaptor with you. Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. Slice Expansion This battery pack increases your computer's...
Page 45 Universal Serial Bus port (USB2.0) × 4, LAN jack. Tablet PC Pen Tablet PC Pen can be purchased from your TOSHIBA dealer. Use it as a spare to your computer. Spare pen tip and draw-out tool are included. Reserve Pen Reserve Pen can be purchased from your TOSHIBA dealer.
Page 46 Introduction Ultra Slim Bay options The following modules can be installed in the Ultra Slim Bay. All other modules are options. Ultra Slim Bay HDD An adaptor lets you install an optional hard disk Adaptor drive described in Chapter 8, Optional Devices.
Page 47: The Grand Tour
PORTÉGÉ M400 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons) For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Click the Front with the display closed Figure 2-1 shows the computer’s front with its LCD display panel in the closed position.
Page 48 The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality.
Page 49: Left Side
The Grand Tour Left side Figure 2-2 shows the computer’s left side. Universal Serial bus Cooling vents PC card (USB 2.0) ports eject button PC card slot i.LINK (IEEE1394) port Security lock slot Figure 2-2 The left side of the computer Cooling vents Cooling vents help CPU keep from overheating.
Page 50: Right Side
The Grand Tour Keep foreign objects out of the PC card slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury.
Page 51: Back Side
The Grand Tour Bridge media slot The Bridge media slot indicator glows green indicator when the computer is accessing the SD card slot. Ultra Slim Bay A DVD-ROM&CD-R/RW drive, DVD Super Multi drive and Ultra Slim Bay HDD adaptor can be installed in the Ultra Slim Bay.
Page 52 The Grand Tour ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...
Page 53: Underside
Be sure to lock the Ultra Slim Bay latch before you transport or carry the computer. Notches Notches on the computer engage hooks on the TOSHIBA Express Port Replicator to ensure a secure connection. Reserve Pen Reserve Pen is contained in the Reserve Pen case of Underside.
Page 54 One screw secures the Ultra Slim Bay latch. screw Docking port This port enables connection of an optional TOSHIBA Express Port Replicator and a Slice Expansion Battery described in Chapter 8, Optional Devices. Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry.
Page 55: Front With The Display Open
LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle. Display screen TOSHIBA Assist button TOSHIBA Presentation button Fingerprint Sensor Stereo speaker ESC/Rotation button (Right) LCD Sensor switch...
Page 56 The default setting is TOSHIBA Assist. When power-off, standby and hibernation, press this button to start the computer and launch the program. You can specify the function of TOSHIBA Assist button in the TOSHIBA Controls properties. 2-10 User’s Manual...
Page 57 Hibernation Mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.
Page 58: System Indicators
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. Figure 2-7 System indicators DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
Page 59: Keyboard Indicators
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 60: Usb Floppy Disk Drive
The Grand Tour USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. It is supplied as standard with some models and as an option with others. USB connector Disk-In-Use Indicator Floppy disk...
Page 61: Optical Media Drives
The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVD- ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical media drives...
Page 62: Formats
The Grand Tour Formats The drives support the following formats: ■ ■ CD-ROM DVD -Video ■ ■ DVD-ROM CD-Text ■ ■ CD-DA CD-ROM Mode 1, Mode 2 ■ ■ Enhanced CD (CD-EXTRA) Photo CD (single/multi-session) ■ ■ Addressing Method 2 CD-ROM XA Mode 2 (Form1, Form2) DVD-ROM&CD-R/RW drive...
Page 63: Dvd Super Multi Drive Double Layer
The Grand Tour DVD Super Multi drive Double Layer The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/ DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
Page 64 For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.
Page 65: Getting Started
PORTÉGÉ M400 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 66: General Conditions
PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.
Page 67: Placement Of The Computer
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.
Page 68: Seating And Posture
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Figure 3-1 Posture and positioning of the computer ■...
Page 69: Lighting
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■...
Page 70: Strategic Rest Breaks
Operating the computer in Tablet mode TOSHIBA PORTÉGÉ M400 computer can be used in two ways; ordinary laptop PC and Tablet PC. You can use the computer as Tablet PC that is operated with attached Tablet PC Pen by turning LCD display panel in 180 degrees and closing it.
Page 71 Getting Started When operating the computer in tablet mode, follow the instructions below. Figure 3-2 Operating the computer in tablet mode ■ Hold the computer firmly on your forearm. Do not block the vent. ■ Remove the connector of AC adaptor from the computer when using the computer in tablet mode held in your forearm.
Page 72 Getting Started ■ The display panel works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Tablet PC Pen inside the display area when you use it near the edges of the display panel.
Page 73: Connecting The Ac Adaptor
Power and Power-Up Modes. ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
Page 74 Getting Started 1. Connect the power cord to the AC adaptor. Figure 3-4 Connecting the power cord to the AC adaptor (2-pin plug) Figure 3-5 Connecting the power cord to the AC adaptor (3-pin plug) The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model.
Page 75: Opening The Display
Getting Started Opening the display The computer’s LCD display panel can be opened in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer to unlatch the display panel. 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly.
Page 76: Starting Up For The First Time
Getting Started 2. Slide and hold the computer’s power button. Power button Figure 3-8 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen.
Page 77: Standby Mode
■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, slide the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
Page 78: Hibernation Mode
1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
Page 79 For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.
Page 80: Restarting The Computer
Getting Started Data save in Hibernation Mode When you turn off the power in Hibernation Mode, the computer takes a moment to save current memory data to the hard disk. During this time, the HDD indicator will light. After you turn off the computer, and the content of memory has been saved to the hard disk, turn off the power to any peripheral devices.
Page 81: Restoring The Preinstalled Software From The Recovery Hdd
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
Page 82 Getting Started 3-18 User’s Manual...
Page 83: Operating Basics
PORTÉGÉ M400 Chapter 4 Operating Basics This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Page 84: Using The Tablet Pc Pen And Reserve Pen
Tablet PC Pen in a natural position and tap, press or trace on the screen lightly. Before you begin using the TOSHIBA PORTÉGÉ M400 for the first time, you will need to calibrate the Tablet PC Pen. Refer to the...
Page 85 The lead cannot be replaced if it is worn (Reserve Pen only). TOSHIBA is not liable to the quality problem of the products due to the use of the Tablet PC Pen in an environment where above conditions are not satisfied because of the use by unspecified number of users.
Page 86: Removing The Tablet Pc Pen
Operating Basics Removing the Tablet PC Pen Remove the Tablet PC Pen as described below. 1. Gently push the Tablet PC Pen down. The pen rises up slightly. Tablet PC Pen slot Tablet PC Pen Tablet PC Pen slot Tablet PC Pen slot Figure 4-3 Removing the Tablet PC Pen 2.
Page 87: Double Tap
■ TOSHIBA recommends the customer to keep another pen set as a spare. You can buy the pen set from TOSHIBA dealer. Do not use the broken pen tip. When it breaks, replace it with a refill delivered with the Tablet PC Pen.
Page 88: Removing The Reserve Pen Case
Operating Basics Removing the Reserve Pen case To remove the Reserve Pen case, follow the steps below. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4.
Page 89: Storing And Removing The Reserve Pen From The Reserve Pen Case
Operating Basics Storing and Removing the Reserve Pen from the Reserve Pen case Follow the procedures below to remove the Reserve Pen from the Reserve Pen case. Removing the Reserve Pen from the Reserve Pen case 1. Lift the Reserve Pen up from the Reserve Pen case by its end. Reserve Pen Reserve Pen case Figure 4-8 Removing the Reserve Pen from the Reserve Pen case...
Page 90: Changing To The Tablet Mode
Operating Basics Changing to the Tablet mode To change the laptop mode to the Tablet mode, follow the instructions below. Figure 4-10 Changing to the Tablet mode (1) ■ Place the computer on a stable, flat place such as a desktop and rotate the LCD display panel slowly, holding the panel at its lower part.
Page 91 Operating Basics 2. Rotate the LCD display panel clockwise slowly. Figure 4-11 Changing to the Tablet mode (2) Do not apply excessive rotating force to the LCD display panel. It causes damage of the LCD display panel. 3. Turn the display latch in 180 degrees to the down side. 4.
Page 92: Changing The Screen Orientation
Operating Basics 7. Press the LCD display panel downward softly. Display latch Slit Figure 4-13 Changing to the Tablet mode (4) Changing the screen orientation The orientation of desktop screen can be changed to one of the following four display modes: Secondary portrait Primary portrait Primary landscape...
Page 93: Method 1: Changing The Screen Orientation Using Toshiba Accelerometer Utilities And Toshiba Rotation Utility
Method 2: Changing the screen orientation using Cross Function Button 1. Press Cross Function Button for more than one second. TOSHIBA Table Menu will appear. 2. Select the Internal Monitor of the Toshiba Shortcut using Cross Function Button and press Cross Function Button.
Page 94: Method 3: Changing The Screen Orientation Using Task Bar
3. Select “changing the screen” from the Screen Orientation pull down menu and change the screen. You can set the orientation of the desktop screen just after rotating the display from [Start]-[All Programs]-[TOSHIBA]-[Tablet PC]-[TOSHIBA Rotation Utility] Using Accelerometer Utilities When you shake the computer: ■...
Page 95: Changing To The Laptop Mode
Operating Basics It is safe that you hold the computer with both hands horizontally as shown in the example. The computer is shaken horizontally. The computer is shaken perpendicularly. Figure 4-15 Shake the computer Changing to the laptop mode To change the Tablet mode to the laptop mode, follow the instructions below.
Page 96: Points To Note About The Fingerprint Sensor
Operating Basics Points to note about the Fingerprint Sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects.
Page 97: How To Delete The Fingerprint Data
Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Page 98: Points To Note About The Fingerprint Utility
Operating Basics Align your fingertip with the sensor as shown in the drawing and swipe. Points to note about the Fingerprint Utility Backups for saved fingerprint data and saved information in the PasswordBank can be performed in Import or Export User Data under Fingerprint Software Management.
Page 99: Window Logon Via Fingerprint Authentication
Operating Basics You can also start User Enrollment Wizard using the following method. ■ Click the Protector Suite QL icon in the Task Bar. ■ Swipe your finger across the Fingerprint Sensor. 2. Click Next. 3. The User’s Password screen is displayed. Ensure the same Windows logon username is displayed before entering a password into the Enter your password field.
Page 100: Fingerprint Power-On Security
■ It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.
Page 101: Fingerprint Single Sign-On Feature
User/BIOS Password and Windows Logon Password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.
Page 102: How To Swipe The Finger
TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Page 103: Using The Usb Floppy Disk Drive
Operating Basics Using the USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. It is supplied as standard with some models and as an option with others.
Page 104: Changing Ultra Slim Bay Modules
RW drive, DVD Super Multi drive and HDD adaptor. To avoid injury, do not put your hand into the Ultra Slim Bay slot. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction for information on using this utility to change modules while the computer’s power is on.
Page 105: Inserting A Module
Operating Basics 6. Grasp the optical media drive and slide it out. ■ The optical media drive and other Ultra Slim Bay modules can become hot with use. Be careful when removing the module. ■ Store the DVD Super Multi drive unit in the Ultra Slim Bay Case when removing it from the computer or transporting it.
Page 106: Using Optical Media Drives
Operating Basics Using optical media drives The text and illustrations in this section refer primarily to the optical media drive. However, operations are the same for other optical drives in the Ultra Slim Bay. The full-size drive provides high-performance execution of CD/ DVD-ROM-based programs.
Page 107 Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Figure 4-20 Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-21 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.
Page 108: Removing Discs
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/ DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
Page 109: How To Remove Cd/Dvd When The Disc Tray Will Not Open
Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Page 110: Before Writing Or Rewriting
RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
Page 111: When Writing Or Rewriting
Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data will be lost if there is a write error. ■...
Page 112: Important Message
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 113 Operating Basics DVD-R DL: (Double Layer supported model only) MITSUBISHI CHEMICAL CORPORATION DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: (Double Layer supported model only) MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW:...
Page 114 Operating Basics ■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in whole or in part. ■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and DVD- RAM disc cannot be recovered. Check the content of the disc carefully before you delete it.
Page 115: When Writing Or Rewriting
Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...
Page 116: Data Verification
Operating Basics ■ You might not be able to use the “Exact Copy” function of RecordNow! to back up a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder. ■ If you add data to a DVD-R and DVD+R disc that you have already recorded to, you might not be able to read the added data under some circumstances.
Page 117: Dla For Toshiba
Operating Basics DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable. ■ DLA does not support formatting and writing to a DVD-RAM disc - these functions are performed by DVD-RAM Driver Software.
Page 118: How To Make A Dvd-Video
Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] - [InterVideo WinDVD Creator] to launch WinDVD Creator. 2. Click [Capture] button then capture the video data from the DV- Camcorder via IEEE1394.
Page 119 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
Page 120: Media Care
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 121: Sound System
Operating Basics 8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields.
Page 122: Toshiba Mic Effect
For more instructions for this software, click start, point to All Programs, point to TOSHIBA, point to Utilities and click TOSHIBA Mic Effect Help. 4-40 User’s Manual...
Page 123: Modem
Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 124: Properties Menu
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system.
Page 125: Connecting
Operating Basics Connecting To connect the modular cable, follow the steps below. The modular cable that comes with the computer must be used to connect the modem. Connect the end of the modular cable with the core to the computer. ■...
Page 126: Disconnecting
Operating Basics Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner.
Page 127: Bluetooth Wireless Technology
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™...
Page 128: Bluetooth Tm Stack For Windows ® By Toshiba
This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth other than TOSHIBA mobile PCs. Release Notes related to the Bluetooth Stack for ®...
Page 129: Wireless Communication Switch
Operating Basics Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off. ■...
Page 130: Lan
Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Page 131: Disconnecting Lan Cable
Operating Basics 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN jack LAN connector Figure 4-26 Connecting the LAN cable...
Page 132: Moving The Computer
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it recommends changing the function of HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter.
Page 133: Using The Hard Disk Drive (Hdd) Protection
Operating Basics Using the Hard Disk Drive (HDD) Protection This computer has a function for reducing the risk of damage on hard disk drive. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and those signs in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact.
Page 134: Toshiba Hdd Protection Properties
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting.
Page 135: Details
Operating Basics Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Figure 4-29 Details Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
Page 136: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.
Page 137: The Keyboard
PORTÉGÉ M400 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 138: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 139: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
Page 140 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters the Standby Mode.
Page 141 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 142: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 143: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 144: Temporarily Using Normal Keyboard (Overlay On)
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...
Page 145: Temporarily Changing Modes
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
Page 146 The Keyboard 5-10 User’s Manual...
Page 147: Power And Power-Up Modes
PORTÉGÉ M400 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 148 Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) Secondary • Operates • No charge adaptor battery fully • No charge • LED: Secondary connected charged • LED: Secondary battery green battery green DC IN green DC IN green Secondary •...
Page 149 When the main battery is not charging. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a Slice Expansion battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
Page 150: Power Indicators
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Secondary battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the Secondary battery indicator to determine the status of the Slice Expansion battery.
Page 151: Power Indicator
The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User's Manual.
Page 152: Slice Expansion Battery (Provided With Some Models, Or Option)
The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 153: Care And Use Of The Battery Pack
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
Page 154 Do not turn on the PC's power again until an authorized Toshiba service provider has checked it for safety. Continued use could cause a fire or rupture possibly resulting in serious injury or PC failure including but not limited to the loss of data.
Page 155 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Use only battery packs recommended by TOSHIBA as replacements. 2. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted correctly and securely. If the battery falls out, while you are carrying the PC, you could be injured or the battery pack could be damaged.
Page 156: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 157: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 158: Retaining Data With Power Off
Power and Power-Up Modes ■ Cooling Method ■ System standby ■ System Hibernation ■ Monitor Power off ■ HDD Power off ■ How often and how long you use the hard disk, optical disc and the floppy disk drive. ■ How much charge the battery contained to begin with.
Page 159: Replacing The Battery Pack
Power and Power-Up Modes 3. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the Battery indicator flashes or there is some other warning to indicate a low battery, go to step 4.
Page 160 Power and Power-Up Modes 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Close the LCD display panel and turn the computer upside down. 5.
Page 161: Toshiba Password Utility
Battery lock Figure 6-3 Securing the battery pack 9. Turn your computer over. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Page 162 ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held...
Page 163: Supervisor Password
If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 164: Starting The Computer By Password
Power and Power-Up Modes Starting the computer by password If you have already registered a password, there are three ways to start the computer: ■ Insert an SD card token before you turn on the computer. The computer will start normally, without displaying a password prompt. ■...
Page 165: Tablet Mode
Chapter 3, Getting Started. Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation.
Page 166: Panel Power On/Off
Power and Power-Up Modes Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power will be turned on in Standby Mode or Hibernation Mode but not in boot mode. If the panel power off function is enabled and you manually shut down Windows, do not close the computer’s LCD display panel until the shut down process has been completed.
Page 167: Hw Setup
PORTÉGÉ M400 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
Page 168: Power On Display
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
Page 169: Boot Priority
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM* and LAN (Default).
Page 170 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Ultra Slim Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
Page 171 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. The priority is set as Built-in HDD 1 ->...
Page 172 HW Setup USB Memory BIOS Support Type Set the type of the USB memory as a startup device. Set the type of the USB memory to be equivalent to the HDD (Default). * Based on the [HDD] order in the [Boot Priority Options] item.
Page 173: Device Config
HW Setup Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enables Wake-up on LAN. Enabled Disables Wake-up on LAN (Default). Disabled Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Page 174: Configuring The Execute-Disable Bit Capability And Tpm
■ In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the...
Page 175 HW Setup Select either the Execute-Disable Bit Capability or settings in the security controller to make changes. Please refer to the operating instructions displayed in the settings screen. Ending the BIOS Setup Program Save the changes and end the program. 1.
Page 176: Execute-Disable Bit Capability
Capability so that it is not available for use. (Default). System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
Page 177: Diagnostic Mode
■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
Page 178 HW Setup 7-12 User’s Manual...
Page 179: Optional Devices
PORTÉGÉ M400 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ Bridge media slot ■...
Page 180: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 181: Removing A Pc Card
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped.
Page 182: Media Care
Optional Devices Media care Observe the following precautions when handling the card. Card care ■ Do not twist or bend cards. ■ Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid. ■...
Page 183: Removing An Sd Card
Optional Devices 2. Press gently to ensure a firm connection. SD card Bridge media slot Figure 8-3 Inserting an SD card ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost.
Page 184: Memory Stick/Memory Stick Pro
TOSHIBA SD memory card format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
Page 185: Xd Picture Card
Optional Devices Write protection Memory Stick can be write protected to safeguard your data. To write- protect a Memory Stick, slide the lock on the back of the Memory Stick to the lock position. Inserting a Memory Stick To insert a Memory Stick, follow the steps below. 1.
Page 186: Inserting An Xd Picture Card
Optional Devices Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury. Inserting an xD picture card To insert an xD picture card, follow the steps below.
Page 187: Memory Expansion
When you install or remove a memory module, ensure that you do not touch any other internal areas of the computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following...
Page 188: Installing Memory Module
Optional Devices Installing memory module There are slots for two memory modules. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning on the power section in Chapter 3, Getting Started.
Page 189 Optional Devices 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest.
Page 190 Optional Devices 10. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot.
Page 191: Removing Memory Module
Optional Devices Do not bend the keyboard ribbon cable. 13. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and place the keyboard down. When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard.
Page 192: Battery Pack
Optional Devices 6. Grasp the sides of the module and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Page 193: Slice Expansion Battery
Optional Devices Slice Expansion Battery This battery pack increases your computer's operating time when a main battery pack is also installed. For details on using the battery pack, follow the steps below. Connecting the Slice Expansion Battery Follow the steps below to connect the Slice Expansion Battery to the computer When handling Slice Expansion Battery, be careful not to short circuit the terminals.
Page 194: Disconnecting The Slice Expansion Battery
Optional Devices Disconnecting the Slice Expansion Battery Follow the steps below to disconnect the Slice Expansion Battery to the computer. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4.
Page 195: Battery Charger
Optional Devices Battery Charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). HDD Kit (Serial-ATA) An extra hard disk drive expands the flexibility of your system and lets you carry your data without carrying the computer.
Page 196: Installing The Hdd Kit (Serial-Ata)
Optional Devices 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Connector Plastic tab Hard disk drive pack Figure 8-19 Removing the hard disk drive pack Installing the HDD Kit (Serial-ATA) To install the HDD Kit (Serial-ATA), follow the steps below.
Page 197: Ultra Slim Bay Hdd Adaptor
Optional Devices Ultra Slim Bay HDD Adaptor You can increase your computer’s data storage capacity by installing an additional 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Ultra Slim Bay. To install a hard disk drive in the Ultra Slim Bay HDD adaptor follow the steps below.
Page 198: Usb Fdd Kit
Optional Devices 3. Close the lid and slide the lock to the lock position. Figure 8-23 Closing the lid For details on inserting the Ultra Slim Bay HDD adaptor in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics.
Page 199: I.link (Ieee1394)
Optional Devices 2. Connect the monitor cable to the external monitor port and tighten the screws on the left and right hand side. External monitor port Monitor cable Figure 8-24 Connecting the monitor cable to the external monitor port 3. Turn the monitor’s power on. 4.
Page 200: Precautions
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 201: Disconnecting
Refer also to the documentation that came with your i.LINK device. TOSHIBA Express Port Replicator In addition to the ports available on the computer, the TOSHIBA Express Port Replicator. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source.
Page 202: Security Lock
Optional Devices Security lock Security locks enable you to anchor your computer and optional TOSHIBA Express Port Replicator to a desk or other heavy object to help prevent unauthorized removal of the computer or TOSHIBA Express Port Replicator. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot.
Page 203: Troubleshooting
PORTÉGÉ M400 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 204: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 205: Hardware And System Checklist
Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
Page 206: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 207: Ac Power
Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing green AC power If you have trouble turning on the computer with the AC adaptor connected,...
Page 208 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...
Page 209: Password
Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.
Page 210: Internal Lcd Display Panel
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
Page 211: Dvd-Rom&Cd-R/Rw Drive
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the Optical Drive Power icon in the task tray and turn on the power.
Page 212: Dvd Super Multi Drive
Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
Page 213: Usb Floppy Disk Drive
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive.
Page 214: Sd Card
Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an Make sure the card is not write protected. SD memory card You cannot read a file Make sure the target file is on the SD memory...
Page 215: Pointing Device
Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to return to its Pad operation normal shape and try again to move it.
Page 216: Fingerprint Sensor
Troubleshooting USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume its mouse operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.
Page 217: Usb Device
Troubleshooting USB device Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the USB ports on the computer and the USB device. work Make sure the USB device drivers are properly installed.
Page 218: Sound System
Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Page 219: I.link (Ieee1394) Device
Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not Make sure the cable is securely connected to the function computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon.
Page 220: Lan
Troubleshooting Problem Procedure Character display In data transmission, make sure the parity bit and becomes garbled stop bit settings correspond with those of the during a remote computer. communication Check the flow control and communication session protocol. You cannot receive an Check the rings before auto answer setting in incoming call your communications application.
Page 221: Disposing Of Pc And Pc Batteries
Troubleshooting Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer. The built-in Bluetooth function and an optional Bluetooth PC card cannot operate simultaneously.
Page 222: Toshiba Support
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 223 Troubleshooting Outside of Europe In Europe Singapore Spain TOSHIBA Singapore Pte. Ltd. TOSHIBA Information Systems, ESPAÑA 438B Alexandra Road #06-01 Parque Empresarial San Fernando Alexandra Technopark Edificio Europa, l Planta, Singapore 119968 Escalera A 28830 Madrid United States of America...
Page 224 Troubleshooting 9-22 User’s Manual...
Page 225: Legal Footnotes
PORTÉGÉ M400 Chapter 10 Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual.
Page 226: Memory (Main System)*2
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 227: Lcd*5
Legal Footnotes Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Page 228 Legal Footnotes 10-4 User’s Manual...
Page 229: Appendix A Specifications
PORTÉGÉ M400 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.18 kilograms, configured with: 12.1”XGA, 512MB RAM, 40GB HDD, DVD-ROM&CD-R/RW drive, modem, LAN, Wireless LAN, 6cell battery pack, Table PC Pen. Weight will vary with other configurations. Above weights are measured at specific criteria.
Page 230 Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands...
Page 231 Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
Page 232 Specifications User’s Manual...
Page 233: Appendix B Display Controller And Modes
PORTÉGÉ M400 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel.
Page 234 Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character Colors Scanning matrix frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K Text Characters 2, 3 80 × 25 8 × 8 16 of 256K Text Characters...
Page 235 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Colors Scanning mode matrix frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
Page 236 Display Controller and Modes Table 2 Video modes (XGA model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual with LCD only) 1600 ×...
Page 237 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual with LCD only) 1600 ×...
Page 238 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual with LCD only) 1600 ×...
Page 239 Display Controller and Modes Table 3 Video modes (SXGA+ model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K 1400 × 1050 256/256K 256/256K 1600 ×...
Page 240 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K 1400 × 1050 64K/64K 64K/64K 1600 ×...
Page 241 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M 1400 × 1050 16M/16M 16M/16M 1600 ×...
Page 242 Display Controller and Modes B-10 User’s Manual...
Page 243: Appendix C At Commands
PORTÉGÉ M400 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 244 AT Commands Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default). Selects V.21 when the modem is at 300 bps. Selects Bell 103J when the modem is at 300 bps (default).
Page 245 AT Commands Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default). Modem goes off-hook. Result Codes: n=0,1 ERROR Otherwise Request ID information This command displays product information about the modem.
Page 246 AT Commands Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
Page 247 AT Commands Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 248 AT Commands Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
Page 249 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
Page 250 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
Page 251 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
Page 252 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
Page 253: Appendix D S-Registers
PORTÉGÉ M400 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
Page 254 S-registers Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
Page 255 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
Page 256 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units:...
Page 257 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
Page 258: At Command Set Result Codes
S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
Page 259 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
Page 260 S-registers User’s Manual...
Page 261 PORTÉGÉ M400 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 262 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
Page 263 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
Page 264 V.90 User’s Manual...
Page 265: Card Specifications
PORTÉGÉ M400 Appendix F Wireless LAN Card Specifications Form Factor PCI Express Mini Card ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. ■...
Page 266 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 267 Wireless LAN 2457* 2462 2467* 2472* *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
Page 268 Wireless LAN 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 User’s Manual...
Page 269 Please refer to the TOSHIBA RAID help for details. ■ By changing this setting you are reconfiguring your hard disk.
Page 270: Windows Manual Setup
3. When the message "Setup will load support for the following mass storage device(s):" appears on the screen, press the S key and install the TOSHIBA RAID Driver using the TOSHIBA RAID Driver Disk that was created. 4. Follow the onscreen instructions to continue Windows setup.
Page 271 An effective way to ensure that such situations do not happen is to carry out RAID-1 media checks regularly. The TOSHIBA RAID utility is set as default to carry out media checks every month on the third Wednesday from noon.
Page 272: Starting The Bios Setup Program
TOSHIBA RAID Starting, Modifying and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If Password = is displayed, enter the User Password and press the Enter key. Please refer to Chapter 6, the...
Page 273: Ending The Bios Setup Program
TOSHIBA RAID 3. The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings.
Page 274 TOSHIBA RAID User’s Manual...
Page 275 Appendix H Bluetooth wireless technology Interoperability Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
Page 276 TOSHIBA portable computers. Always use Bluetooth Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe...
Page 277: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 278 -Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
Page 279 FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used in this device are located at the upper edge of the LCD screen, and this device has been tested as portable device as defined in Section 2.1093 of FCC rules when the LCD screen is rotated 180 degree...
Page 280 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 281: Device Authorization
Bluetooth wireless technology Interoperability Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law. The Name of the radio equipment: EYXF3CS JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D05-0074001...
Page 282 Bluetooth wireless technology Interoperability User’s Manual...
Page 283: Ac Power Cord And Connectors
PORTÉGÉ M400 Appendix I AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
Page 284 AC Power Cord and Connectors France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
Page 285 BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
Page 286 TOSHIBA Anti-theft Protection Timer User’s Manual...
Page 287 PORTÉGÉ M400 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
Page 288 Glossary IDE: integrated drive electronics I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory...
Page 289 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
Page 290 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
Page 291 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 292 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 293 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 294 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 295 Glossary I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps.
Page 296 Glossary megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions.
Page 297 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 298 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
Page 299 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 300 Glossary Glossary-14 User’s Manual...
Page 301 6-10 hinge 2-9 extending life 6-12 opening 3-11 indicator 2-12 screen 2-9 location 2-7 DLA for TOSHIBA 1-16 4-35 monitoring capacity 6-11 Docking port 1-8 real time clock 1-4 Documentation list 1-2 safety precautions 6-7 DVD Super Multi drive 1-6...
Page 302 Index lighting 3-5 HDD indicator 2-12 seating and posture 3-4 HDD Protection 1-12 work habits 3-5 Heat dispersal 1-12 4-54 External monitor 1-7 8-20 Hibernation 1-13 problems 9-16 Hot keys 1-11 display selection 5-5 instant security 5-4 Fingerprint Sensor Internal LCD screen bright- location 2-9 ness decrease 5-5 problems 9-14...
Page 303 Index Windows special keys 5-7 Keypad overlay 1-11 Password Arrow mode 5-7 power on 1-11 Numeric mode 5-8 problems 9-7 temporarily using normal starting the computer by 6- keyboard (overlay on) 5-8 Supervisor 6-17 temporarily using overlay user 6-15 (overlay off) 5-8 PC card 1-8 turning on the overlays 5-7 inserting 8-2...
Page 304 TOSHIBA Express Port Replica- Processor 1-3 tor 1-19 8-23 TOSHIBA Mic Effect 1-16 RecordNow! 1-15 4-33 TOSHIBA Mobile Extension 1- Recovery HDD 3-17 Recovery Media 3-17 TOSHIBA PC Diagnostic Tool 1- Restarting the computer 3-16 TOSHIBA Power Saver 1-13 Index-4 User’s Manual...
Page 305 Index TOSHIBA Presentation button 1-11 TOSHIBA SD Memory Boot Util- ity 1-15 TOSHIBA Zooming Utility 1-15 TV 8-21 Ultra Slim Bay 2-5 changing modules 4-22 HDD adaptor (Black) 8-19 location of slot 2-4 options 1-20 USB 1-7 location 2-5 problems 9-15...
Page 306 Index Index-6 User’s Manual...

Toshiba Portege M400 User Manual

Appendix B Display Controller and Modes

Preface

Manual Contents

Conventions

General Precautions

Stress Injury

Heat Injury

Pressure or Impact Damage

PC Card Overheating

Mobile Phone

Introduction

Equipment Checklist

Features

Appendix E

Special Features

Utilities

Options

The Grand Tour

Front with the Display Closed

Left Side

Right Side

Back Side

Underside

Front with the Display Open

System Indicators

Keyboard Indicators

USB Floppy Disk Drive

Optical Media Drives

AC Adaptor

Getting Started

Setting up Your Work Space

Operating the Computer in Tablet Mode

Connecting the AC Adaptor

Opening the Display

Turning on the Power

Starting up for the First Time

Turning off the Power

Restarting the Computer

Create Optical Recovery Discs

Restoring the Preinstalled Software from the Recovery HDD

Restoring the Preinstalled Software from Your Creating Recovery Media

Operating Basics

Using the Touch Pad

Using the Tablet PC Pen and Reserve Pen

Changing to the Tablet Mode

Changing the Screen Orientation

Using Accelerometer Utilities

Changing to the Laptop Mode

Using the Fingerprint Sensor

Using the USB Floppy Disk Drive

Changing Ultra Slim Bay Modules

Using Optical Media Drives

Writing Cds on DVD-ROM&CD-R/RW Drive

Writing CD/Dvds on DVD Super Multi Drive

Media Care

Sound System

Modem

Wireless Communications

Lan

Cleaning the Computer

Moving the Computer

Using the Hard Disk Drive (HDD) Protection

Heat Dispersal

The Keyboard

Typewriter Keys

Function Keys: F1

Soft Keys: Fn Key Combinations

Hot Keys

Windows Special Keys

Keypad Overlay

Generating ASCII Characters

Power and Power-Up Modes

Power Conditions

Power Indicators

Battery Types

Care and Use of the Battery Pack

Replacing the Battery Pack

TOSHIBA Password Utility

Tablet Mode