Table of Contents
Advertisement
OPERATION OF TOUCH CONTROL PANEL
Before Operation
* Before operating your new oven, make sure you read and
understand this operation manual completely.
1) Plug in the oven. Nothing will appear in the display at
this time.
2) Open the door. The display shows "0".
3) Close the door.
4) Control panels can only be operated when the door is
closed.
5) Your oven has 3 ways to select memory numbers.
See CUSTOM SETTING 1. To Set Input Method on page
9. The factory setting is Dual digit Input .
Cancellation:
1. Cooking data is canceled when keys are not pressed for
more than three minutes when setting programming.
2. Cooking stops when the STOP/CLEAR pad is pressed and
cooking data remains. However if subsequent keys are not
If you do not operate the oven for 3 minutes or more (i.e. closing the door or pressing the STOP key), your oven will
automatically shut down, so you will not be able to operate the oven until you open and close the oven door.
NOTE : When you set Demonstration mode or while cooking fan work after cooking, your oven will not shut down
automatically.
HELPFUL TIPS for the Memory Input Method
The Memory Input Method determines how to input memory numbers for Memory Cooking and Custom Setting and Saving
Memories, therefore follow the method below. Refer to HELPFUL TIPS below as well as to Memory Cooking below.
1. Dual Digit Input: Must input two numbers to select a
memory, even though the fi rst number is 0. Memory
programming is limited to 0 - 99.
2. Single Digit Input: Can only input one number to select
a memory. Memory programming is limited to 0 - 9.
3. Repeat Digit Input: Input one, two, or three numbers to
select a memory. Memory programming is limited to 0 - 29.
4. For Repeat Digit Input/Auto Start ON only, push number
pads within one second of the previous number.
5. Regardless of input method selected, Counter Check/Clear (Custom Setting 7) and Multiplication Factors for Double/
Triple Quantity (Custom Setting 10) only use the Dual Digit Input method. As for Custom Setting 10, enter memory
number after pressing the DOUBLE/TRIPLE QUANTITY pad.
MEMORY OPERATION
Memory Cooking
* Your oven has 100 memory banks from 0 to 99. Memory
contents from memory number 0 to 29 are the same in
Dual, and Repeat Digit Input methods.
* Memory 0 - 9 are programmed as factory settings. See
the table of Programmed Memories and the Memory
Input Method on the right side. Memory 10 - 99 must
be programmed before using Memory Cooking. When a
memory number which has not been programmed is
entered, "End"
will be shown in the display. See
Saving Memories on page 15-19 to programme
a new memory.
R-1900J [EN].indd Sec1:5
R-1900J [EN].indd Sec1:5
pressed within three minutes, cooking data will be canceled.
To resume cooking press the START pad.
3. Cooking stops when the door is opened and cooking data
remains. However once the door is closed, cooking data will
be canceled if subsequent keys are not pressed within
3 minutes. To resume cooking press the START pad.
4. Cooking is immediately canceled by pressing the STOP/
CLEAR pad twice.
Checking food:
Press the STOP/CLEAR pad then open the door, check food,
close the door and press the START pad to continue
cooking.
Cooking Completion:
When food is not taken out after cooking completion, "End"
will be shown in the display until the food is taken out.
The Memory Input Method
Memory No.
Examples
Memory
0
Input Method
Dual Digit Input
0, 0
Single Digit Input
0
Repeat Digit Input
0
Programmed Memories and the Memory Input Method
Dual
Single
Memory
Digit
Digit
No.
Input
Input
1
01
1
2
02
2
3
03
3
4
04
4
5
05
5
6
06
6
7
07
7
8
08
8
9
09
9
0
00
0
5
2
12
22
0, 2
1, 2
2, 2
2
2
2, 2
2, 2, 2
Repeat
Cook
Output
Digit
time
power
Input
1
5 sec.
100%
2
10 sec.
100%
3
20 sec.
100%
4
30 sec.
100%
5
40 sec.
100%
6
50 sec.
100%
7
1 min.
100%
8
1 min. 15 sec.
100%
9
1 min. 30 sec.
100%
0
2 min.
100%
4/28/09 10:01:25 AM
4/28/09 10:01:25 AM
Advertisement
Table of Contents
