Samsung RAC Series Technical Data Book page 43

13. Installation
13-2. Outdoor unit
Connecting the Power Terminal
• Connect the cables to the terminal board using the compressed ring terminal.
• Cover a solderless ring terminal and a connector part of the power cable and then connect it.
4(3/8) 9.5(3/8)
4/6
(0.006/
0.009)
8(3/16) 15(9/16)
10(0.01) 8(3/16) 15(9/16)
16(0.02) 8(3/16) 16(10/16) ±0.2 (±0.007)
8(3/16) 12(1/2)
25(0.03)
8(3/16) 16.5(10/16)
8(3/16) 16(10/16)
35(0.05)
8(3/16) 22(7/8)
50(0.07) 8(3/16) 22(7/8)
70(0.10) 8(3/16) 24(1)
• Connect the rated cables only.
• Connect using a driver which is able to apply the rated torque to the screws.
• If the terminal is loose, fire may occur caused by arc. If the terminal is connected too firmly, the terminal may be damaged.
M4
CAUTION
• When connecting cables, you can connect the cables to the electrical part or connect them through the holes below depending on the spot.
•
• Remove all burrs at the edge of the knock-out hole and secure the cable to the outdoor knock-out using lining and bushing with an electrical insulation such
as rubber and so on.
• Must keep the cable in a protection tube.
• Keep distances of 1.97 in. or more between power cable and communication cable.
• When the cables are connected through the hole, remove the Plate bottom.
B D
+0.3(+0.011)
±0.2 (±0.007) 5.6(1/4)
-0.2(-0.007)
+0.3(+0.011)
±0.2 (±0.007) 7.1(1/4)
-0.2(-0.007)
+0.3(+0.011)
9(3/8)
-0.2(-0.007)
+0.5(+0.019)
±0.3 (±0.011) 11.5(7/16)
-0.2(-0.007)
+0.5(+0.019)
±0.3 (±0.011) 13.3(1/2)
-0.2(-0.007)
+0.5(+0.019)
±0.3 (±0.011) 13.5(1/2)
-0.2(-0.007)
+0.5(+0.019)
±0.4 (±0.015) 17.5(11/16)
-0.4(-0.015)
E
3.4(1/8) ±0.2 (±0.007) 6 (1/4)
4.5(3/16) ±0.2 (±0.007) 7.9 (5/16)
5.8(1/4) ±0.2 (±0.007) 9.5 (5/16)
7.7(5/16) ±0.2 (±0.007) 11 (3/8)
9.4(3/8) ±0.2 (±0.007) 12.5 (1/2)
11.4(7/16) ±0.3 (±0.011) 17.5 (11/16)
13.3(1/2) ±0.4 (±0.015) 18.5 (3/4)
AC power : 1(L), 2(N), L, N / Communication : F1, F2
Silver solder
F
5 (3/16) 20 (3/4) 4.3 (3/16)
+0.4 (+0.015)
9 (3/8) 28.5 (1-1/8) 8.4 (1-3/16)
30 +0.4 (+0.015)
9 (3/8) 8.4 (1-3/16)
(1-3/16)
33
13 (1/2) 8.4 (1-3/16)
(1-5/16)
(+0.015) 0(0)
15 (5/8) 8.4 (1-3/16) +0.4 (+0.015)
34
(1-3/8)
13 (1/2) 8.4 (1-3/16)
13 (1/2) 38 (1-1/2) 8.4 (1-3/16)
+0.4 (+0.015)
43
13 (1/2) 8.4 (1-3/16)
(1- 11/16)
+ 0.4(+0.015)
14 (9/16) 50 (2) 8.4 (1-3/16)
+ 0.4(+0.015)
20 (3/4) 51 (2) 8.4 (1-3/16)
t
+0.2
(+0.007)
0(0)
0.9 (0.03)
0(0)
1.15 (0.04)
0(0)
+0.4
1.45 (0.05)
1.7 (0.06)
0(0)
1.8 (0.07)
0(0)
1.8 (0.07)
0(0)
2.0 (0.078)
0(0)
43