Furuno SC-33 Operator's Manual page 30

APPENDIX 1 MENU TREE
130316 (Temperature, Extended Range) (Off, 1000, 2000 msec)
130577 (Direction Data) (Off, 20, 25, 100, 200, 1000, 2000 msec)
130578 (Vessel Speed Components) (Off, 200, 250, 1000, 2000 msec)
130842 (Six Degrees of Freedom Movement) (Off, 20, 25, 50, 100, 200 msec)
130843 (Heel Angle, Roll Information) (Off, 20, 25, 50, 100, 200 msec)
130845 (Multi Sats in View Extended) (Off, 1000 msec)
130846 (Motion Sensor Status Extended) (Off, 1000 msec)
*1
Port Setup Port1 Setup
Port2 Setup (See the menu tree for [Port1 Setup].)
Port3 Setup (See the menu tree for [Port1 Setup].)
Simple Diagnostic Start Diagnostic (Shows the simple diagnostic test results.)
Advanced Diagnostic Start Diagnostic(Shows the advanced diagnostic test results.)
Format (IEC61162-1 Ed.5, NMEA0183 V4.1, NMEA0183 V3.0,
NMEA0183 V2.0, NMEA0183 V1.5)
Talker (GP, GL, GA, GN, HE, HN, HC)
Baud Rate (Port1/2: 4800bps, 38400bps; Port3: 4800bps, 38400bps)
Sentence Information
Output Sentences (msec)
DTM (On, Off)
GGA (Off, 100, 200, 1000, 2000)
GLL (Off, 100, 200, 1000, 2000)
GNS (Off, 100, 200, 1000, 2000)
GSA (Off, 1000, 2000)
GSV (Port1/2: Off, 1000, 2000;
HDG (Off, 20, 25, 100, 200, 1000, 2000)
HDT (Port1: Off, 20, 25, 100, 200, 1000, 2000;
HRM (Off, 20, 25, 100, 200)
POS (Off, 3000, 30000)
RMC (Off, 100, 200, 1000, 2000)
ROT (Port1: Off, 20, 25, 100, 200, 1000, 2000;
THS (Port1: Off, 20, 25, 100, 200, 1000, 2000;
VBW (Port1: Off, 1000, 2000;
XDR (Off, 1000, 2000)
VTG (Off, 1000, 2000)
ZDA (Off, 1000, 2000)
GPatt (Port1: Off, 20, 25, 100, 200, 1000, 2000;
GPhve (Port1: Off, 20, 25, 100, 200, 1000, 2000;
GPimu (Off, 25, 100, 200, 1000, 2000)
GPmsv (On, Off)
hdcom (Sp) (On, Off)
Relayed Sentences
AAM (On, Off)
APB (On, Off)
BOD (On, Off)
BWC (On, Off)
BWR (On, Off)
RMB (On, Off)
TLL (On, Off)
XTE (On, Off)
SDmrk (On, Off)
Load Rate (Shows the communication load rate.)
AP-2
Port3: Off, 1000, 2000)
Port2: Off, 20, 25, 100, 200, 1000, 2000;
Port3: Off, 20, 25, 100, 200, 1000, 2000)
Port2/3: Off, 20, 25, 100, 200, 1000, 2000)
Port2/3: Off, 20, 25, 100, 200, 1000, 2000)
Port2/3: Off, 1000, 2000)
Port2/3: Off, 20, 25, 100, 200, 1000, 2000)
Port2/3: Off, 20, 25, 100, 200, 1000, 2000)
*1 : Setting is required
at installation.