Dolby Pro Logic - Philips FW798W/22 User Manual

SETTING UP FB219W (
for model FW798W only)
3 Set the CHANNEL slide at the back of
both active surround speakers to the
same number as on the transmitter.
4 Switch on both active surround
speakers.
Note:
– Always be sure that the transmitter and
the active surround speakers are
switched to the same transmitting
channel, otherwise no sound or only a
distorted sound will be heard on the
surround speakers.
Switching On . Standby . Off
The transmitter is equipped with a
sensitive input. If there is no signal on the
SUB and SURR input the transmitter and
the surround speakers will switch to
standby after approximately 100 seconds.
The green light on the front of the active
surround speakers shows that the speakers
are on. If the red light is on, the speakers
has switched to standby. To switch the
active speakers off, use the POWER switch.
If the red light on the front of the
transmitter is off, it has switched to
standby. To switch the transmitter off,
unplug the AC/DC adapter from the power
source.
Untitled-7 15
General Information
Any amplifier or receiver used at high
power can produce distortions which may
seriously damage your speakers. If
distortion occurs, reduce the volume and
the tone control to a level where the sound
is acceptable again.
When using microphones, avoid feedback
which occurs when a microphone picks up
sound from the speakers, resulting in a
howling noise. Keep the microphone away
from the speakers or reduce the volume.
More wireless products ...
The transmitter is also equipped to drive an
optional wireless subwoofer, wireless
stereo speakers or wireless headphones.
Please ask your dealer about these
products. Refer to the instructions provided
with these products before using them
with your transmitter.

DOLBY PRO LOGIC

Dolby Pro Logic
This state of the art Dolby Pro Logic mini
system enables you to experience and
enjoy a Home Cinema sound ambience. The
Pro Logic system allows more accurate
definition of the individual sound sources.
It produces greater sound separation
between channels and provides pinpoint
sound localization. Pro Logic provides four
sound outputs: Left, Center, Right and
Surround (Rear). Front sounds are produced
from the pair of Left and Right speakers
and a Center speaker. The surround sound
is reproduced by two speakers placed at
the rear of the listening area. Although the
surround sound is monaural (single-source),
a pair of speakers is necessary to produce
the correct diffused sound.
This Pro Logic decoder enables you to
decode the following modes: Dolby
Surround, Center Phantom, Dolby 3
Stereo or normal Stereo .
Test Tone
This feature enables you to adjust the Front
Left, Front Right, Center and Surround
Sound levels of the respective speakers in
Dolby Pro Logic mode.
You must sit at the ideal sitting
position and use the remote control to
perform this operation.
6/15/00, 12:50 PM
1 Press CD, TUNER, TAPE or AUX to
switch on the system.
2 Press TEST TONE.
™ A test signal is
generated; it will TEST
UTE
TONE
move through the
CENTER
Left, Center, Right,
and Surround
speakers, in that order.
™ "TEST TONE" followed by
"ADAPT BALANCE, CENTER
AND REAR LEVEL" will be
displayed.
™ The test signal will last for about 90
seconds.
3 Press
BALANCE CENTER
BALANCE
- +
L R
L to adjust
REAR
the sound
- +
of the front
left speaker.
™ The display will show BAL
L+XX.
4 Press BALANCE R to adjust the sound
of the front right speaker.
™ The display will show BAL R
+XX.
5 Press CENTER + or - to adjust the
sound of the center speaker.
™ The display will show either CENT
+XX or -XX.
6 Press REAR + or - to adjust the
sound of the surround speakers.
™ The display will show either REAR
+XX or -XX.
3139 116 18884
15