Table of Contents
Advertisement
Quick Links
Parts and Accessories
Installation Instructions
BMW Apollo car phone retrofit kit
BMW 3 Series Convertible (E 46/C)
The installation time is approx. 5 hours, but this may vary depending on the condition of the car and the
equipment in it.
Retrofit kit No.
Retrofit kit No. 84 61 0 143 955
Installation Instructions No. 01 29 0 146 555
84 61 0 143 955
Issue date: 04.2002
046 0627 Z
Advertisement
Table of Contents
Related Manuals for BMW Apollo 84 61 0 143 955
Summary of Contents for BMW Apollo 84 61 0 143 955
- Page 1 Parts and Accessories Installation Instructions 046 0627 Z BMW Apollo car phone retrofit kit BMW 3 Series Convertible (E 46/C) The installation time is approx. 5 hours, but this may vary depending on the condition of the car and the equipment in it.
-
Page 2: Table Of Contents
Contents Section Page Important information..............Preparations . -
Page 3: Important Information
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used. Target group The target group for these installation instructions is specialist personnel trained on BMW cars with the appropriate specialist knowledge. All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work instructions in a rational order using the prescribed tools (special tools) and observing current health and safety regulations. -
Page 4: Preparations
Preparations TIS instruction No. Conduct a brief test Disconnect the negative pole of the battery 12 00 ... The following components must be removed first of all: Boot trim on the left 51 47 151 Rear seat bench 51 24 005 Rear seat backrest 51 24 010 Front left door sill trim... -
Page 5: Retrofit Wiring Harness Connection Diagram
Retrofit wiring harness connection diagram 046 0490 Z Cable colour / Item Description Signal Connection location in the car Abbreviation / Slot Cross-section Multi wiring harness SW 54-pin plug To transceiver module adapter branch B1 X4038 Fakra plug contact Insulate and tie back X13323 SW 18-pin plug To eject box adapter branch C1... - Page 6 Retrofit wiring harness connection diagram 046 0619 Z Cable colour / Item Description Signal Connection location in the car Abbreviation / Slot Cross-section Transceiver module adapter SW 54-pin plug To multi wiring harness branch A1 X4038 SW 25-pin plug To transceiver module X695 Adapter eject box SW 18-pin plug...
-
Page 7: Installation And Cabling Diagram
Installation and cabling diagram 046 0761 Z Legend Multi wiring harness II Transceiver module adapter Adapter eject box Radio plug X18126 (with SA 660, 661, 662 only) Hands-free microphone Eject box and interface Audio plug X322 Transceiver module Radio plug X18126 (with SA 602, 606, 609, 663 only) Earth post X13016 EN/7 Retrofit kit No. -
Page 8: To Install And Connect The Retrofit Wiring Harness
To install and connect the retrofit wiring harness Install branches A1 – A8 as follows: A9-A12 - Branches A1 - A2 to the installation site of the transceiver module behind the rear seat backrest on the left - Branches A3 - A8 to the left side skirt A3-A8 - Branches A9 - A12 through the cable duct (1) into the boot on the left... - Page 9 To install and connect the retrofit wiring harness Connect branch A12 as follows to plug X18126 : X18126 - WS/BR cable in PIN 10 - WS/GN cable in PIN 11 046 0724 Z Connect branch A11 to plug X18126 . X18126 If the plug X13321 is already in the car, the two cables from branch A9 must be disconnected and...
- Page 10 To install and connect the retrofit wiring harness Disconnect plug X322 . Connect branch A7 in parallel between plug X322 . X322 X322 046 0540 Z Cars with SA 660/661/662 only X18126 Connect branch A6 as follows to plug X18126 : - WS/BR cable in PIN 4 - WS/GN cable in PIN 10 046 0740 Z...
-
Page 11: To Install And Connect The Transceiver Module
To install and connect the transceiver module Insert the transceiver module (1) into the holder (2) and secure the bar (3) with hexagonal screw (4). 046 0329 Z Bolt the strut (1) to the holder (3) using a hexagonal screw (2). 046 0330 Z Connect branch B2 to the transceiver module (1). -
Page 12: To Install And Connect The Eject Box
To install and connect the eject box Connect the telephone cable (1) to the eject box (2). Insert the telephone cable (1) into the cable guide (3) and clip the cable guide (3) together. 046 0308 Z Clip the eject box (1) into the frame console (2). 046 0309 Z Clip the cable guide (1) into the frame console (2). - Page 13 To install and connect the eject box Affix the foam strip (1) to the inside of the holder frame (2). Place the interface (3) on the oddments box (4) and clip in the holder frame (2). 046 0312 Z Connect the black 12-pin plug (1) for the eject box to the interface (2).
-
Page 14: To Install The Hands-Free Microphone
To install the hands-free microphone Connect branch A8 to the hands-free microphone (1). The arrow on the hands-free microphone (1) must point to the front of the car. Clip the hands-free microphone (1) into the ceiling light (2). 046 0765 Z EN/14 Retrofit kit No. -
Page 15: Concluding Work
Concluding work This retrofit system does not require coding. - Conduct a brief test with DIS/MoDiC III. - Conduct a function test - Re-assemble the car EN/15 Retrofit kit No. 84 61 0 143 955 Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002... -
Page 16: Circuit Diagram
Circuit diagram The circuit diagrams for the retrofit telephone system are available if required on the installation instructions CD entitled “Circuit diagrams for retrofit telephones UNI II”. EN/16 Retrofit kit No. 84 61 0 143 955 Installation Instructions No. 01 29 0 146 555 Issue date: 04.2002...