Advertisement
Quick Links
Parts and Accessories
Installation Instructions
BMW Apollo / Classic car phone upgrade kit
BMW X5 (E 53)
These installation instructions are only valid for cars with SA 640
The installation time is approx. 2.5 hours, but this may vary depending on the condition of the
car and the equipment in it.
Retrofit / Installation kit No. 84 63 0 029 299
Retrofit / Installation kit No. 84 63 0 029 299 / 84 63 0 140 413
Installation Instructions No. 01 29 0 140 414
84 63 0 140 413
Issue date: 11.2001
Advertisement
Related Manuals for BMW Apollo 84620029299
Summary of Contents for BMW Apollo 84620029299
- Page 1 Parts and Accessories Installation Instructions BMW Apollo / Classic car phone upgrade kit BMW X5 (E 53) These installation instructions are only valid for cars with SA 640 The installation time is approx. 2.5 hours, but this may vary depending on the condition of the car and the equipment in it.
-
Page 2: Table Of Contents
Contents Section Page Important information ..........Preparations . -
Page 3: Important Information
The target group for these installation instructions is specialist personnel trained on BMW cars with specialist knowledge of vehicle electrical systems. Work: All servicing, repair and installation work on BMW cars is completed at your own risk. All work is to be carried out using current BMW - Repair manuals... -
Page 4: Preparations
Preparations TIS instruction No. Conduct a brief test Disconnect the negative pole of the battery 12 00 ... The following components must be removed first of all: Boot lid trim on the left 51 47 172 Driver seat 52 14 000 Fresh air grille in the rear 64 22 190 Armrest... -
Page 5: Installation And Cabling Diagram
Installation and cabling diagram 053 0029 Z Legend Hands-free microphone Eject box and interface Adapter eject box Transceiver module Transceiver module adapter EN/5 Retrofit / Installation kit No. 84 63 0 029 299 / 84 63 0 140 413 Installation Instructions No. 01 29 0 140 414 Issue date: 11.2001... -
Page 6: Connection Diagram
Connection overview 053 0051 Z Cable colour Abbreviation / Item Description Signal / Cross- Connection location in the car Slot section Adapter eject box Between the standard wiring harness and interface Black 18-pin plug To interface X4545 Black 18-pin plug To plug X4545 on the standard X4545 wiring harness... -
Page 7: To Install And Connect The Transceiver Module
To install and connect the transceiver module Insert the module holder (1) on the left-hand side of the boot (2) and secure it with hexagonal nuts M6 (3) and a hexagonal screw M6 (4). 053 0030 Z Place speed nuts (1) on the module holder (2). 053 0031 Z Connect branch B1 to the black, 54-pin plug X13599 on the standard wiring harness (1). - Page 8 To install and connect the transceiver module Insert the transceiver module (1) into the module holder (2) and secure it with the bar (3) and a hexagonal screw M5 (4). 053 0054 Z EN/8 Retrofit / Installation kit No. 84 63 0 029 299 / 84 63 0 140 413 Installation Instructions No.
-
Page 9: To Install And Connect The Eject Box
To install and connect the eject box Undo the Allen bolts (1) from the armrest (2) and remove the cover (3). 053 0035 Z Take all the springs (1) out of the armrest (2). Remove both bolts (3) with a punch and pull the guide arms (4) upwards. - Page 10 To install and connect the eject box Clip the eject box (1) into the armrest (2). Attach the telephone cable (3) under the guide (4) as shown. 053 0038 Z Screw the cable guide (1) into the armrest (2) and insert the telephone cable (3) as shown.
- Page 11 To install and connect the eject box Install the armrest back on to the centre console. Lay the interface cable (1) and the 6-pin black plug (2) from the eject box as shown. Connect the plug (2) from the eject box and the plug (3) from the interface.
-
Page 12: To Install The Hands-Free Microphone
To install the hands-free microphone Thread the tied back plug X4221 through the microphone opening (1) in the headlining console (2). X4221 053 0044 Z Clip the enclosed hands-free microphone (1) into the microphone trim (2) you removed earlier. Connect plug X4221 to the hands-free microphone (1). -
Page 13: Concluding Work And Coding
Concluding work and coding This upgrade system does not require coding. - Conduct a brief test with DIS/MoDiC. - Conduct a function test - Assemble the car again following the instructions to dismantle it in reverse order. If necessary, the circuit diagram for the telephone preparation (SA 640) and for the adapter cables can be taken from the installation instructions entitled “Telephone upgrade circuit diagrams, part No.