Extron electronics VoiceLift VLP 202 Setup Manual

VoiceLift Microphone Kits • Setup Guide
This guide provides instructions for an experienced installer to install, connect and set up the
Extron VLP 202 VoiceLift Compact Pendant Microphone or the VLH 102 VoiceLift Handheld
Microphone, the VLC 202 Charging Station, and the VLR 102 Receiver in a system with a PVS 407D
PoleVault Digital Switcher.
Set up the charging station first, so the microphone battery can be charged while you install the VoiceLift receiver.
Then set up the microphone and test the system.
Installing the VLC 202 Charging Station
NOTE:
For use with rechargeable NiMH batteries only.
To install the charging station (see the illustration at right):
Plug the wall charger (5 V, 1 A) into a wall outlet
1.
Connect the wall charger cable to the charging station power jack
2.
Install a battery in the microphone(s), following
3.
page. Ensure the microphone is turned off and place it in one of the
slots in the charger 3
LED turns green (this can take up to 5 hours).
NOTE:
Microphones can be left to charge for extended periods. They should be turned off while charging.
CAUTION:
• Do not replace the battery with an incorrect type. Use only NiMh or alkaline batteries.
Ne pas remplacer la pile par le mauvais type de pile. Utilisez seulement des piles de type NiMh ou alkaline.
•
ATTENTION:
• Do not charge alkaline batteries.
• Ne rechargez pas les piles alkalines.
• Be sure to replace the battery with the correct type and to dispose of used batteries appropriately.
• Assurez vous de remplacer les piles par le bon modèle et de jeter les piles usagées de façon appropriée.
Installing the VLR 102 Receiver
To install the VLR 102 IR Receiver in a drop ceiling:
Remove a ceiling tile from the desired location and cut a hole 2 to 3 inches (5.0-7.6 cm)
1.
in diameter 1 .
Separate the receiver base plate
2.
turning the dome (counter clockwise, about an inch) until it comes free.
Align the center of the receiver base plate
3.
Insert the mounting screw
4.
Attach the provided Z-bracket
5.
ceiling tile. Replace the ceiling tile.
Pull a shielded CAT5 cable to the receiver location, and connect one end to the RJ-45
6.
jack 6 (labeled OUT) on the receiver dome
Align the arrow on the dome tab with the raised arrow on the edge of the base
7.
plate . Rotate the dome clockwise until the arrow on the tab aligns with the
7
raised dot on the base plate (
Connect the other end of the shielded CAT5 cable from the receiver to the
8.
VoiceLift RJ-45 connector
PVS 407D PoleVault Switcher
INPUTS INPUTS
1/2 1/2 3/4 3/4
POWER POWER SIG SIG LINK LINK SIG SIG LINK LINK
12V 12V
3 3A MAX 3A MAX
PVT IN PVT IN PVT IN PVT IN
1
step 3
. The charge is complete when the microphone
and the dome
Õ
3 with the hole in the ceiling tile
through the base plate and the hole in the ceiling tile
4
5 to the end of the screw
Ö .
7 inset).
of the PoleVault switcher (see image below).
8
OUTPUT OUTPUT
PVS 407D
5 5 6 6
.
2 .
on the next
by gripping the base plate and
Ö
1 .
4 on the rear side of the
AMPLIFIED AUDIO OUT AMPLIFIED AUDIO OUT AUDIO OUT AUDIO OUT
PAGING PAGING
SENSOR SENSOR
DO NOT DO NOT L L R R
L L R R
GROUND GROUND
OR SHORT OR SHORT
4/8 4/8
SPEAKER SPEAKER
OUTPUTS OUTPUTS
CLASS 2 WIRING CLASS 2 WIRING
REMOTE REMOTE OVER PVT OVER PVT INPUT 5 INPUT 5 AUX AUX
8
RS-232 RS-232 IR IR L L R R
Tx Rx G Tx Rx G S G S G
1
2
3
5
.
1
4
6
Out
1 1 3 3
+V +V
4 4 VLR 102
2 2
LED
1
3
Õ
Base Plate
7
Ö
Dome
1