Specifications; Safety Instructions - Makita HP2070 Instruction Manual

ENGLISH
1 Lock button
2 Switch trigger
3 Speed adjusting dial
4 Higher
5 Lower
6 Lamp
7 Reversing switch
8 Arrow
9 Speed change knob

SPECIFICATIONS

Model
Speed
Concrete
Capacities
No load speed (min
Blows per minute
Overall length
Net weight
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety pre-
cautions should always be followed to reduce the
risk of fire, electric shock and personal injury, includ-
ing the following. Read all these instructions before
attempting to operate this product and save these
instructions.
For safe operation:
1. Keep work area clean
Cluttered areas and benches invite injuries.
2. Consider work area environment
Don't expose power tools to rain. Don't use power
tools in damp or wet locations. Keep work area well
lit. Don't use power tools in presence of flammable
liquids or gases.
3. Guard against electric shock
Prevent body contact with grounded surfaces (e.g.
pipes, radiators, ranges, refrigerators).
Explanation of general view
10 Action mode changing lever
11 Grip base
12 Side grip (auxiliary handle)
13 Teeth
14 Protrusions
15 Chuck key
16 Sleeve
17 Ring
18 Retaining ring
HP2070/HP2070F
High
20 mm
Steel 8 mm
Wood 25 mm
–1
) 0 – 2,900
0 – 58,000
Low
-----
16 mm
40 mm
0 – 1,200
0 – 24,000
364 mm
2.4 kg
4. Keep children away
Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
5. Store idle tools
When not in use, tools should be stored in dry, high,
or locked-up place, out of the reach of children.
6. Don't force tool
It will do the job better and safer at the rate for which
it was intended.
7. Use right tool
Don't force small tools or attachments to do the job
of a heavy duty tool. Don't use tools for purposes not
intended; for example, don't use circular saw for cut-
ting tree limbs or logs.
8. Dress properly
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
9. Use safety glasses and hearing protection
Also use face or dust mask if cutting operation is
dusty.
10. Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
11. Don't abuse cord
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord from heat, oil and sharp
edges.
12. Secure work
Use clamps or a vise to hold work. It's safer than
using your hand and it frees both hands to operate
tool.
13. Don't overreach
Keep proper footing and balance at all times.
19 Hexagonal nut
20 Wrench 19
21 Depth gauge
22 Blow-out bulb
23 Power-ON indicator lamp
(green)
24 Service indicator lamp (red)
25 Vent holes
HP2071/HP2071F
High
20 mm
8 mm 16 mm
25 mm 40 mm
0 – 2,900 0 – 1,200
0 – 58,000 0 – 24,000
362 mm
2.4 kg
Low
-----
5