Akai DR4vr Operator's Manual page 91

Backup
via
SCSI-B Bus
83
The
following procedure describes
how
to
back
up:
J)
Press
th(9
SUB-MENU
key,
then
press the
BACKUP
key
to enter
Backup mode.
2)
Select SCSI
-fa
using the jog
wheel, then press the STORE/ENT
key.
3)
Select the SCSI
ID
number
that
corresponds
to
the external
backup
device.
4)
Select
For yfS
(Format-Yes)
or
For
no (Format-No) using the jog wheel, then
press the
STORE/ENT
key.
This determines whether
or not the
backup
device
will
be formatted before backup
starts.
5)
Select
rh
(all
data)
or
m—ouk
(in-out
data) using the Jog wheel, then press the
STORE/ENT
key.
The
message
surE ??
will
ask you
for
confirmation.
Note: You must
specify the
data for
backup
using
the
IN/OUT
keys
before
you
select ,n-
-out
6)
Press the
STORE/ENT key
to
start
the backup.
If
you
selected
ForS£5
at
step
4,
the external
backup
device
will
be
formatted, then the data
will
be backed
up.
To
cancel
this
setup procedure
or a
backup
that
is in
progress, press the
ESCAPE
key.
Depending on
the
capacity of the backup
device and
the
amount
of
data to
be backed
up, the
message bRFuLL
(BACKUP
FULL) may
appear, especially with
3.5
inch
MO
disks. In
this
case, insert a
new
MO
disk and
press the
STORE/ENT
key.
Backup
will continue.
Number
the
disks sequentially
When
loading data back
into the
DR4vr,
disks
must be
inserted
in the
correct order.
Note: While a backup
is
in progress,
do
not
power
off
a
device or attempt
to eject
an
MO
disk.
7)
When
the
backup
has
finished, the
message
fi ni
5h
will
appear.
Loading Data from a Backup
Device
The
following procedure describes how
to load
(restore)
data from
a
backup
device:
1
)
Press the
SUB-MENU
key, then
press the
LOAD
key
to enter
Load mode.
2)
Select
5f
s;
-t,
using the jog wheel,
and
press the STORE/ENT
key.
3)
Select the SCSI
ID
number
that
corresponds
to
the external
backup
device, then press
the
STORE/ENT
key.
4)
The time
display
will
show
To
load the data
back
to the
same
time
position
that
it
occupied
when
it
was
backed
up, press
the
STORE/ENT
key.
The
message SUrE
PP
will appear. Press the
STORE/ENT
key
again
to
start the loading.
To
load
the data
to
a different time
position, enter a time using
the
numeric keypad,
then press
the
STORE/ENT
key.
The
message sUrE
PP
will appear. Press the
STORE/ENT
key
again
to
start the loading.
Pressing
the
ESCAPE
key during
either
loading or
setting operations
will
cancel
the
corresponding
operation.
If
you
make
a
mistake while
entering
a
time, press the
RESET
key and
will appear,
then
re-enter the correct time.
When
loading data from
a
backup
that
is
split
across a
number
of
MO
disks, the
message
'
nSErt will
appear and
loading
will stop
when
the
DR4vr
requires you
to insert
the next
disk.
Insert the next
disk
and
press the
STORE/ENT
key
If
you
inserted the correct disk,
loading
will continue.
Note: While loading
is in
progress,
do
not
power
off
a
device
or attempt
to eject
an
MO
disk.
Version
4.0 12/95