Installation Without Base; Bebècare - Chicco Oasys 0+ UP BebeCare Manual

above by pressing button P.

2.2 INSTALLATION WITHOUT BASE

To install the child car seat without the base,
proceed as follows:
1. Position the child car seat on the selected
car seat (Fig. 15) rear facing.
2. Pull the vehicle safety belt and fasten it
to the relevant buckle, inserting the hori-
zontal (waist) part of the belt through the
child car seat's two blue slots (K) (Fig. 15).
3. Take the diagonal car safety belt and
thread it through the relevant blue slot (O)
on the back of the child car seat's backrest
(Fig. 16) WARNING! When travelling by car,
this diagonal safety belt must ALWAYS be
threaded through this slot.
4. Pull the belt as tightly as possible, without
leaving any slack and making sure it is
not twisted.
5. Turn the carry handle to position A (Fig. 17).
To remove the child car seat:
1. Release the car safety belt by pressing
the buckle.
2. Bring the carry handle into the position
B (vertical).
3. Unthread the belt through the diagonal
and horizontal slots.
3. BEBÈCARE
BebèCare was designed and developed to
signal the presence of the baby in the car
seat and to notify the user when accidentally
moving away from the car without the baby,
thanks to the presence of sensors integrated
in the car seat.
BebèCare was designed and developed for
use only with minors with a total weight
between 4 and 13 kg.
THIS PRODUCT COMPLIES WITH THE
DIRECTIVE 2012/19/EU.
The equipment works together with the
Bluetooth® Low-Energy standard.
• Frequency ranges: 2.402 GHz – 2.480 GHz
ISM band;
• Channels: 40 channels, each with a band
with equal to 2 MHz;
• Transmission power: - 4 dBm (transmitted
to the antenna);
• Maximum power; 0.398 mW;
• Standard Radio: 802.15.1;
DISCLAIMER
• The use of this equipment does not replace
in any manner the responsibility and/or
supervision of the vehicle driver (and/or
its occupants). BebèCare represents only
a support tool: Never leave the child un-
attended in the car.
• Artsana cannot be held liable in any man-
ner in the case of damaging events and/or
consequences (also related to the incorrect
operation of the electronic equipment) of
any type, as BebèCare is solely intended to
be an aid and alarm to prevent events and/
or consequences caused by forgetfulness.
• BebèCare does not prevent the risk of
serious injuries or death. The use of the
equipment does not in any way replace
the supervision and responsibility of the
driver/caregiver/supervisor/tutor or anyone
who is taking care of the baby.
SAFETY WARNINGS
• For the correct use of the car seat, please
refer to the instructions included in this
manual.
• BebèCare functions only if the fabric lining
of the car seat adheres perfectly to the
body of the car seat.
• After cleaning the fabric lining (CLEANING
THE FABRIC LINING), check that BebèCare
is functioning correctly.
• When cleaning/servicing the car seat, do
not disassemble the BebèCare compo-
nents. The equipment may only be re-
placed if the battery is low and according
to the instructions that will be provided
by Customer Service.
• Make sure that the car seat does not come
into contact with any type of liquid. If liq-
uid comes into contact with the sensor
positioned on the seat and the wetting is
limited, dry it carefully and delicately clean
the surface of the sensor using a dry cloth.
Wait and check again that BebèCare func-
tions correctly. If it does not work or in the
case of doubt, contact Customer Service.
• If the car seat comes into contact with
any type of liquid, BebèCare may stop to
work temporarily until the car seat has
dried completely.
23