Download
Share
Print this page
Toro Workman GTX Series Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Utility Vehicle
  5. Workman GTX Series
  6. Installation instructions manual
Toro Workman GTX Series Installation Instructions Manual

Toro Workman GTX Series Installation Instructions Manual

Steel flat bed kit
Hide thumbs Also See for Workman GTX Series:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
Steel Flat Bed Kit
Workman
Model No. 07148
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
No parts required
Steel cargo bed
Flange-head screw (5/16 x 3/4 inch)
Prop rod U bracket
Prop rod
Flange-head screw (1/2 x 4-1/2 inches)
Locknut (1/2 inch)
T handle
No parts required
Preparing the Machine
1. Park the machine on a level surface.
2. Engage the parking brake.
3. Shut off the engine and remove the key from the key switch.
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
GTX Series Utility Vehicle
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Qty.
–
–
1
3
1
1
2
2
1
–
Register at www.Toro.com.
Prepare the machine.
Remove the plastic cargo bed.
Install the steel cargo bed.
Install stake sides to the steel flat bed (optional).
Figure 1
Original Instructions (EN)
Form No. 3407-632 Rev B
Installation Instructions
Use
All Rights Reserved *3407-632* B
Printed in the USA

Advertisement

loading

Related Manuals for Toro Workman GTX Series

Summary of Contents for Toro Workman GTX Series

  • Page 1 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key from the key switch. Figure 1 © 2016—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3407-632* B...
  • Page 2 Removing the Plastic Cargo 4. Using an overhead hoist, lower the cargo bed. 5. Remove the 2 pivot bolts (1/2 x 4-1/2 inches) and 2 locknuts (1/2 inch) from the pivot bracket located at 1. Using an overhead hoist, raise the plastic cargo bed. the rear of the machine (Figure 2.
  • Page 3 Installing the Steel Cargo Bed 5. Release the cargo-bed lever and raise the cargo bed using an overhead hoist. 1. Remove the 3 flange-head screws (5/16 x 3/4 inch), 6. Slide the short end of the prop rod into the detent prop rod U bracket, and prop rod from the bottom of slot (Figure...
  • Page 4 8. Install the T handle onto the button-head screw (Figure Figure 9 1. Button-head screw 2. T handle 9. Tighten the jam nut (3/8 inch) fully against the T handle (Figure 10). Figure 10 1. Jam nut (3/8 inch) 2. T handle...
  • Page 5 Installing Stake Sides Optional To install the optional stake sides, you need the following measurements and quantities of wood: Wood Dimensions Total Length of Each Board Quantity Needed 38 x 89 mm (2 x 4 inch) 36 cm (14 inches) 29 x 140 mm (5/4 x 6 inch) 117 cm (46 inches) You also need the following hardware:...
  • Page 6 Notes:...
  • Page 7 Notes:...
  • Page 8 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.

This manual is also suitable for:

Workman gtx 07148