Radio Reception; Plug And Play; Tuning To Radio Stations; Presetting Radio Stations - Philips LX8200SA/22S User Manual

Plug and Play

Plug and Play allows you to store all available RDS stations
and radio stations automatically.
First time setup / power up
1 When you turn on the power, " AUTO INSTALL – PRESS
PLAY" is displayed.
2
PressÉ Å on the system to start installation.
➜ "INSTALL TUNER" is displayed, followed by " AUTO
PROGRAM".
➜ The system will automatically store the radio stations
with sufficient signal strength, starting from FM band and
followed by MW band. Weak radio stations may be stored
in later presets.
➜ When all the available radio stations are stored or the
memory for 40 presets are used, the last preset radio
station (or the first available RDS station) will be played.
3
If the first preset is an RDS station, the system will
proceed to set the RDS clock.
➜ "INSTALL TIME" is displayed, followed by "SEARCH
RDS TIME".
➜ When RDS time is read, "RDS TIME" is displayed and
the current time will be stored.
➜ If RDS station does not transmit RDS time within 90
seconds, the programme will exit automatically and the
display will show "NO RDS TIME".
G If the first preset is non-RDS station;
➜ The programme will exit automatically.
To reinstall the Plug and Play
1
In standby mode, hold downÉ Å on the system until
"AUTO INSTALL - PRESS PLAY" is displayed.
2
PressÉ Å again to start installation.
➜ All previously stored radio stations will be replaced.
To exit the Plug and Play
G Press Ç on the system.
➜ If you do not complete the Plug and Play installation, the
function will be restarted when you turn on the power
again.
Notes:
– If no stereo frequency is detected during Plug and Play,
"CHECK ANTENNA" will be displayed.
– During Plug and Play, if no button is pressed within 15
seconds, the system will exit Plug and Play mode.

Radio Reception

Tuning to radio stations

1
Press SOURCE to select TUNER mode (or TUNER on
the remote control.
2
Press TUNER again to select the desired band : FM or
MW.
3 Hold down S or T until the frequency indication
starts to change, then release.
➜ The system automatically tunes to the next strong signal
radio reception.
G To tune to a weak station, press S or T briefly
and repeatedly until an optimal reception is found.
4
Repeat step 3 if necessary until you find the desired radio
station.

Presetting radio stations

You can preset up to 40 radio stations in the memory.
Automatic preset from a desired preset
number
1 In tuner mode, press 1 or 2 or use the numeric keypad
(0-9) to select the desired preset number.
2 Hold down PROG until "AUTO PROGRAM" is displayed.
➜ If a radio station has been stored in one of the presets,
it will not be stored again under another preset number.
➜ If no preset number is selected, automatic preset will
begin from preset (1) and all your former presets will be
overridden.
To exit the preset setting
G Press PROG or Ç on the system.
Manual preset of favourite radio stations
1
Tune to your desired radio station (refer to "Tuning to radio
stations").
2
Press PROG twice.
➜ The preset number starts flashing.
3 Press 1 or 2 or use the numeric keypad (0-9) on the
remote control to select the desired preset number.
4
Press PROG again to store the radio station.
G Repeat steps 1–4 to store other radio stations.
5
To exit, press Ç.
Notes:
– If you attempt to programme more than 40 preset radio
stations, " PROGRAM FULL" is displayed.
– During programming, if no key is pressed within 15
seconds, the system will exit the programme mode
automatically.
R R
25
ADIO ECEPTION