Table of Contents
Advertisement
Adjusting the color convergence
This projection TV uses three separate TV tubes: red, green, and blue.
The red, green, and blue images are projected onto the screen where
they converge to form a full-color picture. You can see a clear picture
only when the three images converge correctly. Convergence may drift
over time or if the TV is moved. If you can see clear images on the
screen, skip this procedure.
Make this adjustment after the TV has been on for at least 30
minutes.
To check and adjust the color convergence:
1. Press MENU, then press x or • until the PICTURE menu
appears.
2. Press y or z to highlight CONVERGENCE (see illustration
below left).
3. Press x or • to display the center CONVERGENCE menu (see
illustration below right).
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
P CTURE ANTENNA
I
7
8
MODE
SPORTS
9
10
11
FLESH TONE
ON
12
NO I
SE
REDUCTION
OFF
13
COLOR
14
TEMPERATURE
COOL
15
CONVERGENCE
16
SAVE NEW
PREFERENCE
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
If you see separate red, blue, or green crossed lines (or red or blue
shadows next to white lines), you need to adjust the convergence.
4. Press ENTER to highlight RED or BLUE, depending on which
color needs adjusting. If both red and blue need adjusting,
perform steps 4 and 5 twice.
5. Press y (up), z (down), x (left), or • (right) on the remote
control to converge the red or blue line into the green line, which
will turn completely white when correctly adjusted. When color
convergence is correctly adjusted, you will see two single white
lines.
6. Press EXIT to close the center CONVERGENCE menu and
open the circumference CONVERGENCE menu (see
illustration below left).
7. Press the corresponding Number button (1–4 and 6–9) to select
the area to adjust.
8. Press ENTER to highlight RED or BLUE (see illustration below
right), depending on which color needs adjusting. If both red and
blue need adjusting in the selected area, perform steps 8 and 9
twice.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
1
2
4
PUSH
1
–
9
7
8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
9. Press yzx • to converge the red or blue line into the green line,
which will turn completely white when correctly adjusted. Repeat
steps 8 and 9 until you see two single crossed white lines.
10. Press EXIT once to select another area to adjust, and then repeat
steps 7–9.
11. Press EXIT twice to close the CONVERGENCE menu.
20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
7
8
9
10
11
12
13
RED
B L U E
14
15
ENTER
:
TO SELECT COLOR
16
EX I T
:
TO SELECT POS I
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
3
2
3
4
5
6
7
8
9
6
10
11
12
13
RED
B L U E
14
15
ENTER TO SELECT COLOR
:
16
9
EX I T
:
TO SELECT POS I
T
I ON
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
RECALL
MUTE
1
2
4
5
8
7
100
0
CH
MENU/
VOL
ENTER
CH
TV
CABLE
VCR
FAV CH
T
I ON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
POWER
3
6
Number
9
CH RTN
ENT
MENU/
ENTER
VOL
yzx •
EXIT
TV/VIDEO
Advertisement
Table of Contents
