Adding Channels To The Tv's Memory; Programming Channels Automatically - Toshiba 42H81 Owner's Manual

Adding channels to the TV's memory

When you press Channel y or z, your TV will select only the
channels stored in the TV's channel memory.
Follow the steps below and on the next page to program all active
channels into the TV's memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and
store them in its memory. After the channels are stored automatically,
you can manually add or erase individual channels (see page 20).
If you use both ANT-1 and ANT-2 terminals, you must program
channels for each input source.
To program channels automatically:
1. Press MENU, and then press x or • until the SET UP menu
appears.
2. Press y or z until TV/CABLE is highlighted.
3. Press x or • to highlight either TV or CABLE, depending on
which you use. If you use an antenna, highlight TV; if you use
cable, highlight CABLE.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
SET UP
7
8
LANGUAGE ENGL SH I
9
CLOCK SET 0 0 : 0 0
10
ANT 1 / 2 ANT 1
11
TV / CABLE TV / CABLE
12
CH PROGRAM
13
ADD / ERASE ADD
14
15
16
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
4. Press z to select CH PROGRAM.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
SET UP
7
8
LANGUAGE ENGL SH I
9
0 0 : 0 0
CLOCK SET
10
ANT 1 / 2 ANT 1
11
TV / CABLE CABLE
12
CH PROGRAM
13
ADD / ERASE ADD
14
15
16
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
5. Press x or • to start channel programming. The TV will
automatically cycle through all the TV or Cable channels
(depending on which you selected), and store all active channels
in the channel memory.
While the TV is cycling through the channels, the message
"Programming Now—Please Wait" appears.
6. When channel programming is complete, the message
"Completed" appears.
7. Press Channel y or z to view the programmed channels.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Note:
To tune the TV to a channel not programmed
in the channel memory, use the Channel
Number buttons on the remote control.
LIGHT RECALL POWER
TV
CABLE
MUTE TV/VIDEO TIMER
VCR
Channel yz
1 2 3
CH
4 5 6
Channel
7 8 9
Numbers
VOL
CH RTN
0
100
ENT
ADV/
POP CH
MENU
MENU/
FAV FAV
ENTER
yzx •
ADV/
POP CH
STOP SOURCE PLAY PIP
REC TV/VCR REW FF
STILL LOCATE SWAP
19