Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hilti PD-S
Summary of Contents for Hilti PD-S
- Page 1 PD-S English Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...
- Page 2 Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...
- Page 3 Information about the documentation About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product. •...
- Page 4 The type designation and serial number are printed on the rating plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information...
- Page 5 General safety measures ▶ Check the product for damage before use. Have damage repaired by Hilti Service. ▶ Check the accuracy of the product if it has been dropped or subjected to other mechanical stresses. ▶ Although the product is designed for the tough conditions of jobsite use, like other measuring instruments it should be treated with care.
- Page 6 Items supplied Laser range meter, belt pouch, 2 batteries, quick-start operating instructions, manufacturer's certificate, safety instructions Other system products approved for use with this product can be found at your local Hilti Store or online at: www.hilti.group | USA: www.hilti.com English...
- Page 7 Technical data PD-S Power supply (2 x) 1.5 V Measuring range 0.2 m ... 60 m (0.6 ft ... 200 ft) Distance measurement accuracy ±1.5 mm (±0.06 in) IEC 60529 protection class (dustproof and sprayproof) IP 54 Operating temperature −10 ℃ …50 ℃...
- Page 8 5.1.2 Switching the product on and off 1. Short-press the ON / Delete / OFF button to switch the product on. 2. Press the ON / Delete / OFF button for 2 seconds to switch the product off. 5.1.3 Switching the acoustic signal on and off ▶...
- Page 9 5.2.1 Taking single measurements 1. Press the ON / Delete / OFF button to activate the laser beam. 2. Aim the laser beam at the target and press the Measure / Continuous measurement button. ◁ The distance is shown in the display. Press the ON / Delete / OFF button once to delete the last measured values.
-
Page 10: Troubleshooting
Troubleshooting If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service. Fault codes If a fault code appears, short-press the Measure / Continuous measurement button to return to the measuring mode. - Page 11 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
- Page 12 English Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...
- Page 13 Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...
- Page 14 Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...
- Page 15 Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...
- Page 16 Hilti = registered trademark of Hilti Corp., Schaan 20180307 Printed: 29.03.2018 | Doc-Nr: PUB / 5410155 / 000 / 00...