Related Manuals for Kohler Precedence K-1355-H1
Summary of Contents for Kohler Precedence K-1355-H1
- Page 1 Precedence Bath Whirlpools: K-1355-H1 K-1356-H1 Copyright E1996 Kohler Co. 114189-2- (9608)
-
Page 2: Important Safety Instructions
Use this unit only for its intended use as denoted in this above the normal body temperature of 98.6 F. The manual. DO NOT use attachments not recommended symptoms of hyperthermia include an increase in the by the Kohler Co. internal body temperature,... -
Page 3: Table Of Contents
Follow the sections that pertain Kohler Co. reserves the right to make changes in to your particular installation. This will help you avoid product characteristics, packaging, or availability at any costly mistakes. -
Page 4: Roughing-In: K-1355-H1, K-1356-H1
30” W x 15” H panel required 25-1/2” 23-1/8” 32” 37-3/4” AIR COMPRESSOR 8-1/2” 60” 1-1/2” PUMP 2-1/2” ACCESS 3/4” 24” 5/8” 3-1/2” 3” 20-1/2” AIR COMPRESSOR 1.25>132 DOOR 2” I.P.S. OPENING 2” O.D. SHOWN WITH APRON REMOVED Kohler Co., Kohler WI 114189-2- (9608) -
Page 5: Product Notices
WARNING: Risk of injury or property damage. Kohler Co. shall not be liable under its warranty or Please read all instructions thoroughly before otherwise for personal injury or damage caused by beginning installation, including the following any such unauthorized modification. -
Page 6: Installation Requirements
Old Bath Floor Protection Boards B. SUBFLOOR PREPARATION Check the flooring under the bath, and make repairs as needed. Make sure the subfloor is level. Kohler Co., Kohler WI 114189-2- (9608) -
Page 7: Remove Aprons And Inspect Unit
32” Min. NOTE: Allow adequate clearance for plumbing. Centerline of drain is 23-1/8” from back of unit. E. PLUMBING PREPARATION Position the plumbing according to the roughing-in dimensions. Cap the supplies, and check for leaks. Kohler Co., Kohler WI 114189-2- (9608) -
Page 8: Before Installing Unit
If the subfloor is not level, some leveling of the whirlpool area will be necessary. Do not support the weight of the whirlpool by the flange. Do not use drywall plaster as a means of support. Drain Hole Shims Kohler Co., Kohler WI 114189-2- (9608) -
Page 9: To Adjust Level
Spacer E. PUMP BANDING STRAP CUT Pump Banding Straps NOTICE: This step is necessary to make your Kohler whirlpool operate more quietly. Pump Base Use tin snips to cut the two banding straps. These Suction Line Support Pan banding straps secure the pump to the support pan during shipping. -
Page 10: Component Location
After the button is depressed, Backup slight pressure inward should open the door. Gasket This unit is different from many other Kohler whirlpools in that the power for the whirlpool pump and controls is supplied through the compressor assembly control box. Hose... -
Page 11: Connect Compressor Box - -H1 Models
Ground must not be (Ground) connected to any current-carrying conductor. Ground To Pump 10. INSTALL WHIRLPOOL TRIM KIT Refer to the installation instructions packed with the trim kit when installing the jet or suction trim. Kohler Co., Kohler WI 114189-2- (9608) -
Page 12: Test Door System
Press in the button on the top of the door, and open the door inward. B. TROUBLESHOOT DOOR SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS... -
Page 13: Water Test Whirlpool & Electronics
Secure the apron to the pan base with screws. Large Apron Supplied Drywall Screw Repeat for the other apron. Small Apron Supplied Drywall Screws Kohler Co., Kohler WI 114189-2- (9608) -
Page 14: Install Finish Wall
After the kick strip is completely applied, go over the Kick strip entire length with firm pressure to secure the kick strip to whirlpool base. Kohler Co., Kohler WI 114189-2- (9608) -
Page 15: Clean-Up After Installation
Rotate the jets so they are facing down toward the basin. Jet Trim Fill the whirlpool to a water level at least 2” above the top of the highest jet. Water temperature in the bath should not exceed 104_F (40_C). Kohler Co., Kohler WI 114189-2- (9608) -
Page 16: Operating Sequence
Reduce Add Air water to whirlpool Air and action, rotate Water Water the flange counterclockwise. To reduce air and water, rotate it clockwise. Shut off whirlpool. Restart whirlpool after 20 minute cycle is complete. Kohler Co., Kohler WI 114189-2- (9608) -
Page 17: Troubleshooting Procedures
Insert the Flexjet into the housing, and lightly push and rotate the Flexjet until it snaps into position. Do not force the Flexjet. O-Ring (Must NOTE: When installed correctly, the Flexjet should turn Be Lubricated) smoothly both clockwise and counterclockwise. Kohler Co., Kohler WI 114189-2- (9608) -
Page 18: Troubleshoot Whirlpool System
B. TROUBLESHOOT WHIRLPOOL SYSTEM This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or a qualified electrician should correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. SYMPTOMS PROBABLE CAUSES RECOMMENDED ACTION 1. - Page 19 Kohler Co., Kohler WI 114189-2- (9608)
- Page 20 114189-2- (9608) Kohler Co., Kohler WI...