Summary of Contents for YASKAWA JVOP-KPLCC04A Series
Page 1
Yaskawa AC Drive Option Bluetooth LCD Keypad Installation Manual Type: JVOP-KPLCC04Axx, JVOP-KPLCC04Mxx To properly use the product, read this manual thoroughly and retain for easy reference, inspection, and maintenance. Ensure the end user receives this manual. MANUAL NO. TOEP C730600 94D...
Page 2
This Page Intentionally Blank YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
• YASKAWA AC Drive GA700 • YASKAWA AC Drive GA800 Drive • YASKAWA AC Drive CH700 • YASKAWA AC Drive CR700 Keypad Yaskawa AC Drive Option Bluetooth LCD Keypad Bluetooth Keypad YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
The symbol marks in this section identify safety messages in this manual. If you do not obey these safety messages, the hazards can cause serious injury, death, or damage to the products and related equipment and systems. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
• If you damage or lose manuals, contact a Yaskawa representative or the nearest Yaskawa sales office shown on the rear cover of the manual, and tell them the document number on the front cover to order new copies.
Page 9
• Monitor drive operation status ◆ Compatible Products Drive Drive Software Version GA500 GA700 1016 or later GA800 CH700 CR700 Refer to "PRG" on the drive nameplate for the software version number. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Make sure that the model number on the option nameplate and the model number on the purchase order are the same. If you have problems with the option, contact the distributor where you purchased the option or the Yaskawa sales office immediately. ◆...
Table 4.1 Component Names and Functions Name Functions RUN LED Illuminates while the drive is operating the motor. ALM LED Illuminates when the drive detects a fault. microSD The slot for a microSD card. Card Slot YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 12
This will also stop the motor when a Run command is active at an external Run command source (REMOTE Mode). To disable priority, set o2-02 = 0 [STOP Key Function Selection = Disabled]. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 13
Factory use for maintenance. Terminal RJ-45 Connects to the drive using an RJ-45 8-pin straight through UTP Connector CAT5e extension cable or keypad connector. Clock Cover for the clock battery. Battery Cover YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 14
RUN Command], the drive can start suddenly. Before you change the control source, remove all personnel from the area around the drive, motor, and load. Sudden starts can cause serious injury or death. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
• The drive received a DC Injection Braking command. • The voltage of the main circuit power supply decreased, and the 24 V power supply is supplying power only the the drive. The motor is stopped. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 16
LED Flashing Statuses Refer to Figure 4.2 for information about the differences between flashing and “flashing quickly”. Figure 4.2 LED Flashing Statuses Figure 4.3 Relation between RUN indicator and Drive Operation YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
If you bend the cables too much, it can break the wires and loosen connections. Note: Use Yaskawa connection cables or recommended cables only. Incorrect cables can cause the drive or option to function incorrectly. ◆...
Yaskawa Drive Cloud account Member ID and Password. Note: • Access the URL on the back cover of this manual to register for an account. • For Japan: Member ID and password to the Yaskawa product and technical information website Setting value of A1-12 [Bluetooth ID] Note: When A1-12 = 0000, Bluetooth communication is disabled.
• For Android devices: Google Play Store • For iOS devices: App Store Table 5.1 QR Codes Google Play Store App Store Refer to Table 5.2 for operating systems and drives compatible with the DriveWizard Mobile App. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Smart Device iOS 10, 11, 12 • Support for Bluetooth 4.0 or 4.1 ■ Enabling Bluetooth Communications Push two times on the initial Setup screen. Push to select [Parameters] then push YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 21
5 Installation and Primary Operation Select [A Initialization Parameters] then push Select [A1 Initialization] then push Select [Bluetooth ID] then push YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 22
Mode when you push a key other than • When the keypad is idle for longer than 60 seconds, the keypad will automatically go back to Bluetooth Mode, even after you change to Normal Operation Mode. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Tap [Log In] to Log into DriveWizard Mobile. Use your Drive Cloud ID and password. If you do not have an account, tap [New Member Registration] to create an account before you continue. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 24
5 Installation and Primary Operation Tap [Help and Product Manuals] on the Home Screen, select the drive model to connect, and download the product information. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 25
5 Installation and Primary Operation Tap [Smart Operator]. Select [Bluetooth] then tap [Connect]. Note: This dialog screen is only for Android smart devices. Skip this step for iOS devices. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 26
5 Installation and Primary Operation YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 27
[Drive Information] menu in DriveWizard Mobile to change the "Serial Number" to a different value. • If you did not download the product information of the connected drive, download the product information as specified by the dialog. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 28
Make sure that the LED status ring of the connected drive is flashing. When you install the Bluetooth keypad on a GA500 drive, the drive will not have an LED status ring. Figure 5.4 LED Status Ring YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 29
Check the [Save Bluetooth ID] checkbox to skip this step in the future. When you connect the drive and your smartphone or tablet, the smart device will show the list of U1: [Operation Status Monitors]. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
DriveWizard Mobile to operate the drive. ■ Disconnect Bluetooth Communications The operation to disconnect Bluetooth communications is different for different operating devices. Table 5.3 lists the disconnection methods for each operating device. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
The operation of the keypad and smart device in Bluetooth Mode is different for different keypad versions. If you use a Bluetooth keypad with REV: C or earlier, refer to Bluetooth Mode (REV: C or YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Bluetooth communications and change to Normal Operation Mode. When the keypad is idle for longer than 60 seconds, the keypad will automatically go back to Bluetooth Mode, even after you change to Normal Operation Mode. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Table 5.4 Key Functions Function Stops drive operation and switches the keypad to Normal Operation Mode. Shows the confirmation screen to disconnect Bluetooth Mode. Select [YES] to switch to Normal Operation Mode. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
• The keypad is waiting for the smartphone or tablet to enter the Bluetooth ID. There is a problem with the connection to the smartphone or tablet. Note: After 2 seconds, the drive goes back to the connection standby screen. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Yaskawa Drive Cloud account Member ID and Password. Note: • Access the URL on the back cover of this manual to register for an account. • For Japan: Member ID and password to the Yaskawa product and technical information website Setting value of A1-12 [Bluetooth ID]...
Tap [Log In] to Log into DriveWizard Mobile. Use your Drive Cloud ID and password. If you do not have an account, tap [New Member Registration] to create an account before you continue. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 37
5 Installation and Primary Operation YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 38
5 Installation and Primary Operation Tap [Help and Product Manuals] on the Home Screen, select the drive model to connect, and download the product information. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 39
5 Installation and Primary Operation Tap [Smart Operator]. Select [Bluetooth] then tap [Connect]. Note: This dialog screen is only for Android smart devices. Skip this step for iOS devices. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 40
5 Installation and Primary Operation YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 41
[Drive Information] menu in DriveWizard Mobile to change the "Serial Number" to a different value. • If you did not download the product information of the connected drive, download the product information as specified by the dialog. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 42
Make sure that the LED status ring of the connected drive is flashing. When you install the Bluetooth keypad on a GA500 drive, the drive will not have an LED status ring. Figure 5.7 LED Status Ring YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 43
Check the [Save Bluetooth ID] checkbox to skip this step in the future. When the drive connects to your smartphone or tablet, the smart device will show the list of U1: [Operation Status Monitors]. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
DriveWizard Mobile to operate the drive. ■ Disconnect Bluetooth Communications (REV: C or Earlier) The operation to disconnect Bluetooth communications is different for different operating devices. Table 5.8 lists the disconnection methods for each operating device. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 45
3 s to keep the keypad in Normal Operation Mode. –The keypad was idle, for example during Auto-Tuning –The keypad must not switch from Normal Operation Mode to Bluetooth Mode YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Note: When the keypad is idle for longer than 30 seconds, the keypad will automatically go back to Bluetooth Mode, even after you change to Normal Operation Mode. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Key Functions in Bluetooth Mode (REV: C or Earlier) is the only key that operates the same in Bluetooth Mode and Normal Operation Mode. The other keys on the keypad will disconnect from Bluetooth Mode. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
• The keypad is waiting for the smartphone or tablet to enter the Bluetooth ID. There is a problem with the connection to the smartphone or tablet. Note: After 2 seconds, the drive goes back to the connection standby screen. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
The installation procedure is different for different drives. Drive Procedure Page GA700, GA800, CR700, CH700 GA500 ■ Optional Items The optional remote-control extension cable and installation support set are necessary for Internal/Flush-Mount installation. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 50
5 Installation and Primary Operation Contact Yaskawa or your nearest sales representative to order mounting brackets and mounting hardware. Optional Items Model Notes Remote control extension Connects the keypad for remote cable operation. WV001 (1 m (3.3 ft)) • RJ-45 8-pin straight through •...
NOTICE Damage to Equipment. Do not bend the communication cables more than the bend radius specifications. If you bend the cables too much, it can break the wires and loosen connections. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 53
Figure 5.11 External/Face-Mount Installation Push the tab on the top of the drive keypad and carefully pull forward to remove the keypad from the drive. Figure 5.12 Removing the Included Drive Keypad YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 54
Remove the keypad connector and put the keypad connector in the holder on the front cover. A - Holder C - Keypad connector B - Hook Figure 5.13 Moving the Keypad Connector to the Holder YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 55
Installation support sets A or B (sold separately) are necessary for Internal/Flush-Mount installation. The installation procedure is the same for installation support sets A and B. Contact Yaskawa or your nearest sales representative to order optional items. Use the dimensions in Table 5.13...
Page 57
Note: Use a gasket between the control panel and the keypad in areas where dust or other airborne unwanted materials could cause damage to the drive. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 58
Figure 5.17 Internal/Flush-Mount Installation Push the tab on the top of the drive keypad and carefully pull forward to remove the keypad from the drive. Figure 5.18 Removing the Included Drive Keypad YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 59
Remove the keypad connector and put the keypad connector in the holder on the front cover. A - Holder C - Keypad connector B - Hook Figure 5.19 Moving the Keypad Connector to the Holder YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 60
Use the extension cable to connect the drive to the keypad. A - Extension cable D - Keypad B - Communications E - Cable connector connector C - Drive Figure 5.20 Connecting the Drive and Keypad with the Extension Cable YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 62
Use a slotted screwdriver to unlock the front cover of the drive. Use a slotted screwdriver with a tip width of 2.5 mm (0.1 in) or less and a thickness of 0.4 mm (0.02 in) or less. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 63
5 Installation and Primary Operation A - Front cover lock Figure 5.23 Unlocking Slide the front cover down and remove it from the drive. Figure 5.24 Remove the Front Cover YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 64
5 Installation and Primary Operation Push on the tab on the right side of the keypad, then pull the keypad forward to remove it from the drive. Figure 5.25 Removing the Included Drive Keypad YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 65
Installation support sets A or B (sold separately) are necessary for Internal/Flush-Mount installation. The installation procedure is the same for installation support sets A and B. Contact Yaskawa or your nearest sales representative to order optional items. Use the dimensions in Table 5.15...
Page 67
Note: Use a gasket between the control panel and the keypad in areas where dust or other airborne unwanted materials could cause damage to the drive. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 68
Use a slotted screwdriver to unlock the front cover of the drive. Use a slotted screwdriver with a tip width of 2.5 mm (0.1 in) or less and a thickness of 0.4 mm (0.02 in) or less. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 69
5 Installation and Primary Operation A - Front cover lock Figure 5.30 Unlocking Slide the front cover down and remove it from the drive. Figure 5.31 Remove the Front Cover YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 70
5 Installation and Primary Operation Push on the tab on the right side of the keypad, then pull the keypad forward to remove it from the drive. Figure 5.32 Removing the Included Drive Keypad YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Use this procedure to replace the battery. WARNING Fire Hazard. Handle keypad batteries properly. Do not charge the battery or disassemble the keypad. If the battery explodes, it can cause a fire. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 72
• Ambient temperature 20 °C (68 °F): 5 years • Ambient temperature -10 °C to +50 °C (14 °F to 122 °F): 3.5 years De-energize the drive and remove the keypad. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 73
• The battery cover side is the positive pole. Make sure that the polarity is correct when you put the battery in the keypad. • Discard the used battery as specified by local regulations. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 74
Figure 5.35 Insert the New Battery Put the battery cover on the keypad and use a slotted screwdriver to turn the battery cover clockwise to close it. Install the keypad on the drive. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Refer to the drive manual for the default setting. 0 : Ramp to Stop 1 : Coast to Stop 2 : Fast Stop (Use C1-09) 3 : Alarm Only 4 : No Alarm Display YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Note: The smartphone or tablet and the keypad could possibly not connect in distances nearer than 10 m (32.8 ft) because of smartphone or tablet specifications. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
◆ European Standards (RE Directives) This product complies with the EU Radio Equipment Directive (RED). Importers, distributors, and manufacturers may be responsible for damages under this RED wireless directive. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Using this device in residential areas may cause harmful interference. The customer shall be responsible for any consequences of using this product in such environments. • Yaskawa may demand the disuse of this product if you or your customer modifies the product. ■...
PC functions that format and delete the data may not be sufficient to fully erase the microSD card data. Yaskawa recommends that customers physically destroy the microSD card in a shredder or use data wipe software to fully erase the card.
-10 °C to +50 °C (14 °F to 122 °F) Operating Ambient Temperature 95% RH or less (no condensation) Operating Ambient Humidity -20 °C to +70 °C (-4 °F to +158 °F) Storage Ambient Temperature (short-term storage temperature during transport) YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Page 81
Table 10.2 Moisture Resistance and Dust Resistance Specifications Item Description Model JVOP- KPLCC04MxA Specification Board surfaces: Apply insulating varnish (HumiSeal) to entire surface of the board excluding connectors. Not supplied with the keypad. Battery for Clock Backup YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
Post-Warranty Repair Period The post-warranty repair period applies to products that are not in the standard warranty period. During the post-warranty repair period, Yaskawa will repair or replace damaged parts for a fee. YASKAWA TOEP C730600 94D Bluetooth LCD Keypad Installation Manual...
11 Warranty There is a limit to the period during which Yaskawa will repair or replace damaged parts. Contact Yaskawa or your nearest sales representative for more information. ◆ Cyber Security Disclaimers This product is designed to transmit and receive data over a network interface.