Memory Tuning; Exchanging Station Positions In Memory - Sangean ATS-909X Manual

SLOW 50kHz 1kHz
AUTO / MANUAL SCAN TUNING
To start Auto Scan Tuning, select band to tune press one
of the Tuning Up / Down buttons for more than 0.5 second.
Once scan starts, release button. The Auto Scan stops as
soon as a station of adequate signal strength is located.
Repeat operation to start scan tuning again. Scan tuning
can be halted by pressing the Tuning Up / Down buttons
momentarily any time during the scanning process.
To manually tune to a frequency of your choice repeatedly,
press and release one of the Tuning Up / Down buttons
until the frequency desired is displayed.

MEMORY TUNING

It is possible to preset up to 406 stations using the memory
capability of the ATS-909X. Each 9 presets compromise 1
page. The SW band is capable of storing 39 pages or 351
preset stations (39 Pages x 9 Presets / Page): 27 Presets
on FM (3 Pages x 9 Presets), 18 Presets on MW (2 Pages
x 9 Presets) and 9 presets on LW.
To Manually Set Memory on FM / MW / LW
Bands
Tune to station you would like to program into memory.
Press Memo button, MEMO will flash in the LCD display,
select page desired by pressing PAGE button. Display
will flash and next available position on display will flash
if an available position is available. If memory is full no
suggested position will flash and LCD will display MEMO
FULL when any button is depressed. Press the Enter
Selection button to assign new frequency to available
flashing open position. If selected button is held for more
than 2 seconds, even with MEMO FULL flashing, newly
selected station will replace existing station.
To Manually Set Memory on SW Band
Tune to station you would like to program into memory.
Press Memo button, MEMO will flash in the LCD display.
Select page desired by using the PAGE button and Rotary
Tuning Knob. Display will flash and next available position
on display will flash if an available position is available.
Press Enter Selection button to assign frequency to
flashing available position. If memory is full no suggested
position will flash and LCD will display MEMO FULL when
any button is depressed. If selected button is held for more
than 2 seconds, even with MEMO FULL flashing. Newly
selected station will replace existing station.
You may change or initiate any page name at any time
by first selecting the page and then pressing the EDIT
button and using the Rotary Tuning Knob to place an
alphanumeric character in the name space in the LCD
Display. Once a character is selected you may move
to the next position to place another character by using
the Tuning Up / Down button. When name is completely
entered press Enter Selection button.
1kHz 1kHz 40kHz
NOTE
You may change and edit your SW band's pages
names, but there is no FM / MW / LW page name. You
may change and edit your FM / MW / LW bands' preset
names, but there is no any SW preset name.
NOTE
Every memory preset memory can be stored including
its frequency, mode (AM / LSB / USB), and fine tuning
frequency.
RECALLING A STATION IN MEMORY
On LW, press ATS / LW button, then press any of the
numbered buttons on the key pad.
On MW / FM, press ATS / MW button or press ATS / FM
button, select desired page by pressing PAGE button and
then press any of the numbered button on the key pad.
On SW, press METER / SW button, select desired page
by pressing PAGE button and rotating the Rotary Tuning
Knob until desired page is selected and then press Enter
Selection button. The receiver will then automatically
search for the strongest frequency on that page. You may
change the selected frequency using the numbered keys
on the key pad.
CANCELING A STATION IN MEMORY
Recall the station in memory, press the MEMO button and
then press the Cancel button (C button).
To LOCK A STATION INTO MEMORY
After programming your stations into memory you may lock
any station into memory to prevent accidental erasure or
elimination should the ATS feature be turned on again.
To lock a station, recall the station you wish to lock and
press MEMO button and then LOCK button. The display
will show memo locked symbol whenever the station is
selected. To remove station from locked position repeat
above procedure and locked symbol will be removed and a
station will no longer in locked state.
EXCHANGING STATION POSITIONS IN
MEMORY
To move a station, in memory to another position recall
station. Press Memo button, MEMO and position display
will flash, press new position desired and a signal will be
heard indicating the exchange has taken place and the
positions have been swapped.
SELECTING AN SW BAND
To select an SW Band, press METER / SW button once
and then press a second time. A flashing m will appear in
the display. Any of the 14 SW bands (11-120m) can now
be selected using the numerical keys on the key pad. The
band selected appears in the LCD display and will remain
GB
F
E
NL
D
06