Advertisement
Quick Links
Advertisement
Related Manuals for ADEMCO TeleSmart
Summary of Contents for ADEMCO TeleSmart
- Page 1 ® K3950V2 3/2/01 (bx)
- Page 2 Introduction ........................3 Features............................... 3 Mounting the Module ..........................3 Wiring Connections ......................4 Programming the System ....................6 Programming Overview..........................6 Programming Steps............................. 7 Downloading .............................. 8 Regulatory Agency Statements ..................9 Size: 3-7/8” W x 7” H x 1-3/8” D (98mm x 178mm x 35mm) Voltage: 10.5VDC-14.5VDC...
- Page 3 • Privacy (turn off the ringer) • Remote access of TeleSMART and security system The TeleSMART Module should be mounted in the security system’s control cabinet if space is available, or within a grounded metal enclosure to provide proper ESD protection.
- Page 4 Refer to the instructions included with the keypad.. You can set TeleSMART keypads to addresses 2-22, 25-30 (addresses 0, 1, 23, 24 are reserved). IMPORTANT: If using VISTA-50P or higher, you must program the following two device addresses when programming the control: address 23 = set as alpha keypad;...
- Page 5 YEL (DATA OUT) control: RED (+12VDC) TO CONTROL'S REAL-TIME CLOCK (RTC) addr 23 = alpha keypad KEYPAD GRN (DATA IN) TERMINALS addr 24 = TeleSmart BLACK (-) GND EARTH GROUND Control Connections RTC and Ground Connections – 5 –...
- Page 6 The User Guide provides detailed information on the system’s options. See the next page for entering program mode and programming steps. The following is a summary of the menu options. Summary of Menu Options Menu Option Used To… Options available to all users Hear Messages listen to messages and memos Record Memo...
- Page 7 PC board, then power up the system with the pins shorted. The system will announce “system ready” after about 20 seconds, indicating the defaults have taken effect. Remove the short across the pins. To program the TeleSmart system, you need to do the following: System Options: Default Menu •...
- Page 8 TeleSmart cannot be in program mode or playback mode when downloading. 1. Central Station dials the TeleSmart phone number 2. TeleSmart answers on the programmed ring count, or, if Answer mode is off, answers on 10th ring. If modem carrier is detected, the downloading session begins.
-
Page 9: Radio Frequency Emissions
RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 10: Industrie Canada
FRQWLQXHG Industrie Canada AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. -
Page 11: Summary Of Connections
KEYPAD GREEN (DATA IN) TERMINALS BLACK (–) GND GRN (DATA IN) REAL-TIME CLOCK (RTC) RED (+12VDC) ARMED AWAY STAY READY BLACK (–) TEST BYPASS MESSAGE INSTANT CODE CHIME YEL (DATA OUT) READY ® KEYPAD EARTH GROUND TeleSMART Summary of Connections... -
Page 12: Ademco Limited Warranty
24 months from the date stamp control on the product or, for products not having an ADEMCO date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be...