Sd-533Hd5 - Pioneer SD-533HD Service Manual

QQ
3 7 63 1515 0
Table 2 OFFSET CONVER DATA
OFFSET CONVER MODE 1
Numeric
Adjustment
Key
Item
1 DFH
2 DFV
3 DF1
4 DF2
5 HPP
6 HPW
7 HTP
8 VTP
OFFSET CONVER MODE 2
Numeric
Adjustment
Key
Item
1 V1D
2 V1C
3 V10
4 VFP
5 HFP
6 H1R
7 HCP
8 H10
The above offset convergence values are common to the
SD-533HD5 and SD-643HD5.
TE
L 13942296513
If the offset convergence values are as indicated in Table 2,
proceed to 3.3. If the values are not the same, adjust the values
with the numeric keys and VOL +/– keys.
Example:
To check DFI in ZOOM mode of OFFSET CONVER. MODE 1
1 Enter the FACTORY mode.
2 Enter the OFFSET CONVER. MODE 1 by pressing the
INPUT 4 key once.
3 Enter the ZOOM screen mode by pressing the SCREEN mode
key once. (When the unit enters FACTORY mode, the screen
mode automatically becomes FULL.)
4 Check the indication on the screen by pressing the numeric
key 3.
Indication at the bottom of the screen : Z DFI 00F
If the adjustment value is 00F, adjustment is not required.
If the adjustment value is other than 00F, adjust with the VOL
+ or VOL- key so that the value becomes 00F.
3.3 Coarse Adjustment of the Green
(Proceed with 3.3 and afterwards when the DIGITAL CONV.
Assy is not replaced.)
Select adjustment items (STATIC and SIZE of vertical and
horizontal lines, etc.) for each GH and GV, and adjust to roughly
eliminate distortion. (For GV, peripheral pin distortion adjust-
www
ment is necessary.)
Press the INPUT 4 key three times to enter OFFSET CONVER.
MODE 3.
.
Press the SCREEN mode key and proceed with the adjustment for
each screen mode.
http://www.xiaoyu163.com
Screen Mode
FULL ZOOM CINEMA NATURAL HD FULL
1D0 1D0 1D0 1D0
0A0 0A0 0A0 0A0
00F 00F 00F 00F
000 000 000 000
14C 14C 14C 14C
00B 00B 00B 00B
02C 02C 02C 02C
033 029 033 02A
Screen Mode
FULL ZOOM CINEMA NATURAL HD FULL
029 082 060 03E
020 020 020 020
000 000 000 000
003 01D 003 01A
122 122 122 122
001 001 001 001
00F 00F 00F 00F
015 015 015 015
x ao
y
i
http://www.xiaoyu163.com
8
The cross-hatch signal is generated inside the unit, and is auto-
matically displayed in OFFSET CONVER. mode and MANUAL
CONVERGENCE mode. You can turn on and off the cross-hatch
signal with the YELLOW key.
1D0
0A0
00F
000
14A
00C
02F
00F
A
Screen mode:
026
F : FULL
Z : ZOOM
01E
C : CINEMA
000
N : NATURAL
036
H : FULL for HD
122
001
The Screen modes change cyclically with each press of the
00F SCREEN mode key.
015
B
Cyclically changes with the CH+ or CH- key as follows:
Q Q
3 6 7 1 3
C
Adjustment items can be selected with the numeric keys.
See Table below.
• Waveforms adjustable in the coarse adjustment
of the green
Numeric Key
0
1
4
6
7
8
D
Adjustment data:
MAX 1FF
100
001
CNT 000
3FF
2FF
u163
MIN 200
Data can be adjusted with the VOL+ and VOL- keys.
.
SD-533HD5, SD-643HD5
2 9 9 4 2 8
Screen indication
STATIC
F RH 001
A B C D
1 5 0 5 8 2 9 9 4
RH RV BH
GV GH BV
GH GV
STATIC STATIC
SKEW SKEW
KEY KEY
PIN PIN
LIN LIN
SIZE SIZE
m
co
9 9
2 8 9 9
129