Programming Tracks; Reviewing The Program - Philips Pro Logic FW-P73 Brochure

All manuals and user guides at all-guides.com
18
• If you wish to change the inner disc
during playback, press DISC
CHANGE again.
™ "DISC CHANGE" will be
displayed.
™ The CD will stop playing.
™ The CD carousel tray will close to
retrieve the inner CD and then
open again with the inner CD
accessible.
3 Press OPEN•CLOSE to close the
CD carousel tray.
Selecting a desired track
Selecting a desired track when
playback is stopped
1 Press í or ë until the desired
track appears on the display.
2 PressÉ to start playback.
™ The selected track number and
elapsed playing time appear on
the display.
Selecting a desired track during
playback
• Press í or ë until the desired
track appears on the display.
™ The selected track number and
elapsed playing time appear on
the display.
• If you press í once it will skip to
the beginning of the current track
and play the track again.
CD
6 Press Ç once to end programming.
Note:
– Pressing í during shuffling can only skip
™ The total number of tracks
to the beginning of the current track.
Searching for a particular
Notes:
passage during playback
– If the total playing time is more than
"99:59" or if one of the
• Press and hold à or á until the
programmed tracks has a number
desired passage is located.
greater than 30, then "--:--"
™ The volume will be reduced.
appears on the display instead of the
• Play returns to normal when à or
total playing time.
á is released.
– If the system is reading the disc,
programming is not possible,

Programming Tracks

"READING" will be displayed and
Programming tracks of a loaded CD is
followed by "DISC X" "X" is the
possible when playback is stopped. The
current read disc number.
display will indicate the total tracks
– During programming, if no button is
stored in the program. Up to 40 tracks
pressed within 20 seconds, the system
can be stored in the memory in any
will exit program mode automatically.
order. When 40 tracks are stored and
you attempt to store another track, the

Reviewing the program

display will show "FULL".
Reviewing of the program is possible
1 Load the desired discs in the disc
only when playback is stopped.
trays.
• Press í or ë repeatedly to review
2 Press PROG to start programming.
the programmed tracks.
™ The starts flashing.
• Press Ç once to exit review mode.
PROGRAM
™ It will cancel any previously
selected repeat mode.
Playing the program
3 Press the CD (CD 1•2•3) or DISC
1 Press É to start program playback.
1/2/3 button to select the disc.
™ "PLAY PROGRAM" will be
4 Press í or ë to select the desired
track.
™ The track number and elapsed
5 Press PROG to store the track.
• Repeat steps 3 to 5 to store other
discs and tracks.
• If you press REPEAT during
program playback, the current track
programmed and total playing or all programmed tracks will be
time appear on the display. played repeatedly.
™ "TRACK" or "PROGRAM" will be
displayed.
™ The
on the display.
2 Press Ç to stop program playback.
Notes:
– If you press any of the CD DIRECT
PLAY buttons, the system will play the
selected disc or track and the stored
program will be ignored temporarily.
The PROGRAM display also will
disappear temporarily from the display.
It will reappear when playback of the
selected disc ends.
– REPEAT DISC mode will be cancelled
when program playback begins.
Erasing the program
playback is stopped)
• Press Ç.
™ "PROGRAM CLEARED" will be
displayed.
Note:
– The program will be erased when the
system is disconnected from the power
supply or when the CD carousel tray is
opened.
displayed.
playing time of the current track
will appear on the display.
and appear
REPEAT PROGRAM
(when
3139 116 19511 ( ENG)