Display Messages - Tascam MD-350 Owner's Manual

Instalación en el estante
Instale esta platina con el juego
de tornillos suministrados como
se ilustra.
Conexiones
... Desconecte la alimentación de todos los ... Asegúrese de insertar firmemente cada
equipos antes de efectuar las cone- enchufe. Para evitar los zumbidos y la
xiones. interferencia, no ate los cordones de
... Lea conexión
las instrucciones de cada
alimentación o al cordón del altavoz.
componente que desea usar con la platina
MD.
Terminales DIGITAL INPUT 1/OUTPUT
Emplee estos terminales para conectar la
ª Conexión
platina a un componente digital (tal como
un reproductor de CD, platina DAT,
Terminales ANALOG INPUT/OUTPUT
amplificador digital, u otra platina MD).
(BALANCED/UNBALANCED)
Emplee estos terminales para conectar la
... Emplee el cable óptico digital opcional
platina a un mezclador, grabadora de cinta (TOS) para la grabación digital. Conecte
cassette u otros componentes. el jack [DIGITAL IN 2] ubicado en el
panel frontal, a un componente digital
tal como una platina de DAT/MD.
Conversión de tensión
(Unicamente modelos de exportación
general)
Desenchufe el cable de alimentación del
tomacorriente de corriente alterna antes
de reposicionar el convertidor de tensión.
1. Ubique el selector de tensión en el
panel posterior.
2. Utilizando un destornillador de extremo
plano, ajuste en la posición adecuada
230 V o 120 V de acuerdo con su zona.
... Para realizar una conexión digital,
extraiga las tapas de los terminales. Si
no emplea los terminales, deje las tapas
junto al cordón de
en su lugar.
ª Cordón de alimentación
Asegúrese de conectar el cordón de
alimentación a un tomacorriente de CA
que tenga el voltaje correcto.
... Sujete el enchufe para enchufar o
desenchufar el cordón de alimentación.
– 92 –

Display Messages

... Track combination may not be The following messages are displayed depending on the operation conditions.
possible.
Tracks created by other editing
operations sometimes cannot be
Message
combined.
... Audio is interrupted during search.
Blank Disc
When a track created by an editing
Cannot Copy !
operation is searched, audio is some-
times interrupted.
Cannot EDIT !
... Track numbers are not assigned
correctly.
Disc Error !
When a CD is recorded through a
digital connection, short tracks may be
Disc Full !!
recorded depending on the contents of
the CD. Also, when auto track marking D-IN UNLOCK !
is performed, the track numbers may
ERASE DISC ?
not be assigned correctly in some
cases.
ERASE TRK ?
... The "TOC Reading" display will not
disappear.
Name Full !!
"TOC Reading" is displayed for a longer
time than usual when a brand-new
NO DISC !!
recordable MD is inserted.
... Note the following when you attempt
No Track !!
to perform recording while erasing
PGM Empty !!
(overwriting) the previous recording:
≠ The remaining recording time of the
PGM Full !!
MD may not be displayed correctly.
≠ After repeated overwrite operations,
Play Mode !!
it may no longer be possible to
overwrite recording. In this case,
Protected !!
first edit the previous recording (by
erasing tracks, etc.) then proceed to
the overwrite operation.
Rec Error !!
≠ The remaining recording time is
Track Full !!
shorter after recording than it was
before recording.
UNDO ?
≠ The overwrite operation is not
recommended if the track to be
UTOC Writing
overwritten contains noise. Since
recording is performed on a 6-
cluster basis (approx. 12 seconds),
over-writing a noisy track may erase
a part of the track.
... It is not possible to assign a track title
during overwrite recording.
... Sometimes the maximum recording
time will not be available even after
performing "ERASE DISC".
In this case, try performing "ERASE
DISC" again. However, you will not be
able to UNDO it afterwards.
... While the LP4 (quadruple long-play)
mode provides exceptional recording
time thanks to advanced compression
technology, very occasionally you may
hear some slight noise, depending on
the material being recorded. We
therefore recommend that if sound
quality is more important for your
recording project than recording time,
you use either the SP (stereo) or LP2
(double long-play) mode.
Description
The recordable MD contains no recorded data.
Copying is not possible.
Editing is not possible.
The data in the MD is abnormal.
No more recording is possible.
Digital input connection is not made.
Is it OK to erase the recorded data on the MD ?
Is it OK to erase this track ?
The title memory is full.
No MD is inserted.
No track has been recorded.
Tracks have not been programmed.
No more tracks can be programmed.
The selected play mode is inappropriate.
The MD is protected against accidental erasure.
A playback-only MD is loaded.
A recording error occurred.
The MD has used up all its track numbers.
Is it OK to cancel the last operation ?
The recorded data is being written on the MD.
– 21 –