Table of Contents
Advertisement
VJ-2606 INSTALLATION MANUAL
6 Installing the ink cartridge
This section explains how to install ink cartridges.
Follow the steps below to install ink cartridges.
1. Turn ON the product.
The printer starts the initializing operation.
After the initial operation is complete, "Start Ink
Charge ->E" is displayed on the operation panel.
2. Press the [Enter] key on the operation manual.
The cleaning fluid which is filled at the factory
shipment is ejected.
After the cleaning fluid is discharged, "Wash Retry?
No" is displayed on the operation panel.
NOTE
When cleaning the head before ink filling, select "Yes"
to press [+] or [-] keys on the operation panel.
Then press [Enter] key and clean the head.
3. Press the [Enter] key on the operation manual.
"Insert InkCartridges" is displayed on the opera-
tion panel.
4. Take out the ink cartridge from the bag and shake
it gently two to three times before installing.
Slots for ink cartridges are specified depending on
the colors of the ink cartridge.
Match the mark on each slot with the color of the
ink cartridge.
Install the ink cartridges with
product.
Insert the cartridge all the way into the product.
1
2
3
4
5
6
7
No.
Name
No.
1
Ink cartridge
5
2
Ink cartridge slot K
6
3
Ink cartridge slot C
7
4
Ink cartridge slot M
"Ink Refill
**%" is displayed on the operation
panel and ink replenishment starts.
The ink replenishment takes about twelve minutes.
Ink filling operation and pause operation are re-
peated during the ink replenishment.
When "100%" is displayed, the ink replenishment
is complete.
VJ2606E-I-01
After the ink replenishment is complete, "SubTank
Refill" is displayed on the operation panel, and the
SubTank Refill is started.
After the SubTank Refill is complete, "Media End"
is displayed on the operation panel.
NOTE
If the Nozzle check printing is performed immedi-
ately after the ink replenishment is complete, the
following results may occur.
Printed line becomes blurred.
The data is not partially printing.
In such cases, follow the Operation Manual "6.2.3
Head cleaning" and charge a small amount of ink.
Then, check the printing result.
If there is no improvement in the print result even
after refilling a small amount of ink, leave the
printer for one hour or more, and refill a small
amount of ink again.
If there is still no improvement, contact MUTOH
local dealer.
mark facing to the
Name
Ink cartridge slot Y
Ink cartridge slot Lc
Ink cartridge slot Lm
7 Loading the roll media
This section describes how to load roll media.
Place the roll media in the center of the printer.
Follow the steps below to load roll media.
1. Loosen the fixing knobs of the right and left rear
2. Place the media on the rail of the feed unit.
3. Lift the left side of the roll media (looking from
4. Set the other side of the roll media in the same
5. Loosen the fixing knobs of the right and left feed
4
feed units, and stretch the knobs wider than the
width of the roll media.
4
1
3
No.
Name
No.
1
Feed unit (Left)
3
2
Feed unit (Right)
4
2
1
No.
Name
No.
1
Rail of the feed unit
2
the rear), attach it to the feed unit, and fix it with
the fixing knob.
3
2
1
No.
Name
No.
1
Feed unit (Left)
3
2
Roll media
way as in step 3.
2
No.
Name
No.
1
Feed unit (Right)
3
2
Roll media
units, move the roll media to the center and tighten
the knobs.
NOTE
Be sure to press the feed units against the printer
while locking them.
1
4
1
3
No.
Name
No.
1
Feed unit (Left)
3
2
Feed unit (Right)
4
4
2
Name
Roll media
Fixing knob
Name
Roll media
Name
Fixing knob
3
1
Name
Fixing knob
2
4
2
Name
Roll media
Fixing knob
(Continue to next)
Advertisement
Table of Contents
