Timer Recording - Sylvania SRC2213B Owner's Manual

•
To stop the OTR operation, press the STOP button
on the TV/VCR or on the remote control.
•
To show the remaining time, press the DISPLAY
button on the remote control so that "OTR"
appears on the TV screen. (It will show up
momentarily then disappear.)
•
Recording stops when 0:00 is reached.
•
Please note that in the SLP mode maximum
recording time, assuming the tape is started at the
beginning, is 8 hours using T-160 (or 6 hours using
T-120).
•
If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediate-
ly, ejects the tape and turns itself off.
•
If you press the power button during OTR, the
TV/VCR continues recording until the selected
length is reached.
1
Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL K or L button.
Remember: If the TV/VCR is connected to a cable
box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be recorded is selected on
the cable box or satellite box.
2
Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3
Begin OTR
Press the REC/OTR button on the
TV/VCR as many times as needed.
The recording length will be deter-
mined by the number of times you
press the REC/OTR button. Each
additional push will increase the recording time by
30 minutes. It is set up to 8 hours.
Push(es) Display
1 push (normal recording)
2 pushes 0:30
3 pushes 1:00
17 pushes 8:00

TIMER RECORDING

You may set the TV/VCR to start and end a record-
ing while you are away. You can set 8 programs to
record on specific days, daily or weekly within a 1
year period.
In the following example, the timer is being set to record:
OTR(2 : 30)
SP
Recording length
30 minutes
60 minutes
480 minutes
- 21 -
DATE: July 4th, 2003
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL: CH61
TAPE SPEED: SP
Make sure ...
•
If a cable box or satellite box is connected with
the TV/VCR you will be limited to record only
one channel. And the channel selector on the
TV/VCR must be selected to the output channel of
the boxes CH 3 or CH 4 and then the actual chan-
nel to be recorded must be selected on the boxes.
•
Clock must be set to the correct time and date
before setting the timer.
•
TV/VCR power must be turn on to program it.
•
Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
•
The channel you want to record is properly set in
advance.
Avoid over lap of programs ...
There is a chance that a program will not be record-
ed when programs overlap;
•
The program with an earlier start has priority.
•
Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
•
The illustration below demonstrates the sequence
of recordings.
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM
*Recording period is SHADED
1
Select "TIMER PROGRAMMING"
Press the MENU button on the
remote control.
Confirm "TIMER PROGRAM-
MING" is pointed by pressing the
PLAY/K button.
And press the F.FWD/B button.
•
If you have not yet set the clock, "MANUAL
CLOCK SET" appears. If so, follow stops [3] to
[8] on page 11. Then set the timer recording.
2
Select your desired program position (1~8)
Press the PLAY/K or STOP/L but-
ton to select the desired program
position.
Then, press the F.FWD/B button.
Recording Sequence
10:00AM 11:00AM 12:00PM
– M E N U –
B TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– TIMER PROGRAMMING –
CH DATE BEGIN END
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
B - - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
- - -/- - - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
EN
1K09