Operation Setup; Ce Conformity Declaration - HITEC X1 Nano Instruction Manual

Operation setup

The X1 Nano is an AC only charger capable of charging Lithium Polymer (LiPo and LiHV) Lithium
Ferrite (LiFe) and Nickel Metal Hydride (NiMH) type batteries. Refer to the following instructions on
how to operate your charger.
LiPo Battery LED Indicator
LiFe Battery LED Indicator
Charge Current Switch
Battery Type Button
Battery Socket
1. Plug the AC power cord in the X1 Nano and a wall socket. All the LEDs will light briefly, the battery
type LED will flash green and red which indicates the charger is ready to use.
2. Select the battery type, either LiPo, LiFe, LiHV or
NiMH, by pressing the BATT TYPE button. The LED
will alternately flash red and green on the battery
type you have chosen.
Select Battery T
2. Selecting the charge current. The X1 Nano has four
charge cur rent settings, either 1, 2, 3 or 4 amps
(1000, 2000, 3000 or 4000mAh). The recommended
charge rate is 1C, whereas battery capacity in mAh
equals the charge current in mAh.
Select Charging Current
Example: If you have a battery pack with a capacity of 2400mAh the 1C charge rate is 2400mA
or 2.4A so you would choose the 2A charge current. If you are charging a pack with a capacity of
2750mAh the 1C charge rate is 2750 mA or 2.75A so you would charge at the 3 amp setting.
AC 100-240V 1. Connect the battery main power connector to the charge lead that is plugged into the main charge
PowerJack outputs on the front of the charger.
LiHV Battery
2. Plug the balance socket into the appropriate (2S, 3S or 4S) balance port on the side of the charger
LED Indicator as shown in the illustration below.
NiMH Battery
LED Indicator
4S Balance Port
3S Balance Port
2S Balance Port
LiPo
Connection diagram
3. The charger will automatically begin charging once the balance connector is plugged in.
The charge status LED will glow in a color according to the "Charge Status Chart" indi cating that
the battery is charging.
When the battery is fully charged, the charge status LED will glow a constant green. Unplug the bat-
tery from the charger and the charge status LED will flash green which indicates the charger is ready
to charge another battery.
NiMH Batteries:
1. Connect the battery's main power connector to the charge lead that is plugged into the main
charge outputs on the front of the charg er.
2. Press and hold the BATT TYPE button for two seconds. The charge status LED will glow in a color
according to the "Charge Status Indicator Chart" indicating that the battery is charging.
When the battery is fully charged, the charge status LED will glow a constant green. Unplug the bat-
tery from the charger and the charge status LED will flash green which indicates the charger is ready
to charge another battery.
TO 100-240V AC Socket
This diagram shows the proper way
to connect the X1 Nano to your Bat-
tery. Failure to connect the battery as
shown in this diagram will damage
the charger. The charger will not
charge Lithium chemistry batteries
without a balance connection.
Charge status indicators
LED green and red blinking The charger is ready to charge
LED glows constant red Battery capacity is less that 25% charged
LEDS blinking red Battery capacity is between 25% and 50% charged
LED blinking yellow Battery capacity is between 50% and 75% charged
LED blinking green Battery capacity is between 75% and 99% charged
LED glows constant green Battery is fully charged
Disposal
This symbol means that it is essential to dispose of electrical and electronic equipment
separately from the domestic refuse when it reaches the end of its useful life. Take your
unwanted equipment to your local communal collection point or recycling centre. This
applies to all countries of the European Union, and to other European countries with
separate waste collection systems.

CE Conformity Declaration

This device has been assessed and approved in accordance with European harmonised
directives. This means that you possess a product whose design and construction fulfil
the protective aims of the European Community designed to ensure the safe operation
of equipment.
If required, you can request MULTIPLEX Modellsport GmbH & Co.KG to supply a copy of
the unit's Conformity Declaration. Please contact the company using the contact details
at the foot of the page.
Errors and omissions excepted. Technical modifications reserved.
Copyright Multiplex Modellsport 2015
Duplication and copying of the text, in whole or in part, is only permitted with
the prior written approval of Multiplex Modellsport GmbH & Co.KG
MULTIPLEX Modellsport GmbH & Co.KG
Westliche Gewerbestr. 1
75015 Bretten · Germany
www.multiplex-rc.de
Multiplex Service: +49 (0) 7252 - 5 80 93 33