Advertisement
Troubleshooting, Hints & Tips
Before requesting service, please make the below checks. If you are in doubt about some
of the check points, or if the remedies indicated in the chart do notsolve the problem, please
contact us.
Problem
Possible Causes
System message
No power supply to
shows "NO
corresponding camera(s)
Connection"
Channel is not paired with
camera yet
Service out of range
Signal been blocked
Camera antenna
connection loss
Low signal or
Antenna directional
unstable signal
limitation
Signal being blocked
Strong radio signal near
by
Strong electromagnetic
interference nearby
Channel(s)
Scan channel(s) been set
disappear during
OFF
auto or manual
scan
Dim/over-bright
Low light vision distance
image at night
too short/too far
time
6
Remedies
First identify the channel number, fi nd
fi nd the corresponding camera. If camera
power status indicator (RED LED) is off,
check power adapter and power cable
connection.
First identify camera has no image, draw
the camera near the receiver then pair
the camera to desired channel. See page
5 for detail. Once pairing completed and
camera is picked up by the receiver,
camera status indicator (GREEN LED)
will light up.
Draw the camera near the receiver
If possible, remove major obstacles
between the camera and the receiver. Or
relocate the camera to proper location.
Secure camera antenna to camera body
tightly.
Adjust camera antenna and receiver
position.
If possible, remove major obstacles
between camera and receiver. Or relocate
the camera to proper location.
Keep WIFI router away from the camera
and/or receiver.
Keep working motors (hair dryer/heat fan/
air conditioner/water pump) or microwave
oven away from the camera and/or
receiver.
Go to the receiver menu and enable
the correct channel(s). See receiver
instructions for details.
Ideal low light vision distance is from 9ft
/ 3m to 25ft / 8m. Adjust the camera to
have camera view fi t in this distance.
Important Safety Precautions
Please read before installing and using this Product. Damage caused by non-compliance with this operating
manual will void the warranty. We will not assume any liability for damages to items or persons caused by
improper handling or non-compliance with the safety notices. Any warranty claim will be null and void in such
cases.
1. Do not drop, puncture or disassemble the camera or receiver; otherwise the warranty will be voided.
2. Keep adapters away from moisture.
3. Never tug on the power cords. Use the plug to unplug it from the wall outlet.
4. Do not expose the camera or receiver to extreme high temperatures or aim the lens in direct sunlight. Doing
so may damage the camera.
5. Use the devices with care. Avoid pressing hard on the camera or receiver body.
6. For your own safety, avoid using the camera or power off the camera when there is a storm or lightning.
7. Remove the power adapter during long periods between usages.
8. Use only the accessories and power adapters supplied by the manufacturer.
9. To meet the regulations pertaining to parental responsibility, keep the devices out of the reach of infants.
10. Check power cables do not get crushed or damaged by sharp edges whenever the devices are in operation.
FCC Compliance Statement:
This device complies with Part 15 of the
FCC Rules. Operation is subjected to the
following two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
FCC/CE WARNING
This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15
of the FCC rules and ETSI (EN) 300 328. These limits are designed to provide reasonable protection against
harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television equipment reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Move the equipment away from the receiver.
- Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for additional suggestions.
You are cautioned that any change or modifi cations to the equipment not expressly approved by the party
responsible for compliance could void Your authority to operate such equipment.
Disposal
If the camera system no longer functions or can no longer be repaired, it must be disposed of according to the
valid statutory regulations. Disposal of spent batteries / accumulators:
You are required by law (Battery Ordinance) to return all spent batteries and accumulators.
Disposing of spent batteries/accumulators with common household waste is prohibited!
Batteries/accumulators that contain hazardous substances are marked with the symbols
on the side. These symbols indicate that it is prohibited to dispose of these batteries/
accumulators in the household waste.
The abbreviations for the respective heavy metals are: Cd= cadmium, Hg= mercury, Pb=
lead. You can return spent batteries and accumulators that can no longer be charged to the
designated collection points in your community, outlets or wherever batteries or accumulators
are sold. Following these instructions will allow you to fulfi l the legal requirements and
contribute to the protection of our environment!
Products with CE Marking comply with
EMC Directive (2004/108/EC); Low Voltage
Directive (73/23/EEC); R&TTE(1999/5/EC)
issued by the Commission of the European
Community. Compliance with these
directives implies conformity to the following
European Norms:
EMC: EN 301 489
LVD: EN 60950
Radio: EN 300 328
3
Advertisement
