Table of Contents
Advertisement
Quick Links
Installation Job Aid for Avaya Virtual
Services Platform 8400
Support
Go to the Avaya Support website at
documentation, product notices, and knowledge articles. You can also search for release notes,
downloads, and resolutions to issues. Use the online service request system to create a service
request. Chat with live agents to get answers to questions, or request an agent to connect you to a
support team if an issue requires additional expertise.
Safety messages
Caution:
To protect the switch against ESD damage, take the following measures before you connect
data cables to the device:
• Always use antistatic wrist straps. Make sure you adjust the strap to provide good skin
contact.
• Ensure that you properly ground work surfaces and equipment racks for protection against
electrostatic discharge. You must connect the common point to the building ground wire. In
a properly wired building, the nearest reliable ground is typically at the electrical outlet.
• Avoid contact between equipment and clothing. The wrist or ankle strap protects only the
equipment from ESD voltages on the body; ESD voltages on clothing can still cause
damage.
• Avoid touching any connector pins.
• Do not remove the wrist or ankle strap until the installation is complete.
Caution:
When you mount this device in a rack, do not stack units directly on top of one another. You
must secure each unit to the rack with appropriate mounting brackets. Mounting brackets
cannot support multiple units.
©
2015 Avaya Inc.
http://support.avaya.com
Installation Job Aid for Avaya Virtual Services Platform 8400
for the most up-to-date
Release 4.2
NN47227-305
Issue 01.06
June 2015
1
Advertisement
Table of Contents
Related Manuals for Avaya 8400
Summary of Contents for Avaya 8400
- Page 1 When you mount this device in a rack, do not stack units directly on top of one another. You must secure each unit to the rack with appropriate mounting brackets. Mounting brackets cannot support multiple units. © 2015 Avaya Inc. Installation Job Aid for Avaya Virtual Services Platform 8400...
-
Page 2: Technical Specifications
Warning: The lithium battery is not field replaceable. It should be removed and replaced by authorized personnel only. Contact Avaya Technical Support for assistance if the battery requires replacement. Warning: Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. -
Page 3: Installing An Ethernet Switch Module
• Visually inspect the connectors for damage before you insert the module. If you insert a module with damaged connectors you will damage the switch. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400... - Page 4 1. Remove the two screws that secure the module bay cover to the chassis. (Save the module bay cover for possible future use.) 2. Slide the module into the bay. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
-
Page 5: Installing A Power Supply
• If you only have one power supply, you can install it in either PSU1 or PSU2. • If you install a second power supply, neither one acts as a primary power supply. The two power supplies load share equally. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400... -
Page 6: Installing An Ac Power Supply
4. Once you install a power supply, you can connect the AC power cord to the power supply on the back of the switch, and then connect the cord to an AC power outlet. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400... -
Page 7: Ac Power Supply Specifications
The 800 W AC power supply uses an IEC 60320 C16 AC power cord connector. The AC power cord is in close proximity to the hot air exhaust, and supports high operating temperatures. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400... -
Page 8: Ac Power Cord Specifications
United States of America, Canada, and Japan: • 100 or 120VAC • NEMA5-15P male plug • 50–60 Hz • UL-recognized (UL stamped on cord jacket) • Single phase Table continues… June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400... -
Page 9: Installing A Dc Power Supply
Installing a DC power supply Important: Avaya does not support installing a combination of AC-input and DC-input power supplies in the same chassis. The VSP 8404 supports two field-replaceable 800 W power supplies. One comes with the switch and you can install a second power supply to provide redundancy and load sharing. - Page 10 DC power to the VSP 8404. Allow at least 30 seconds for the switch to fully power down before restoring power. Otherwise, the switch might produce a core file during the reset leading to an extra delay during boot time. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 11 4. Once you install a power supply, use the following steps to connect the DC power supply wiring assembly: a. Avaya supplies a DC power supply wiring assembly to connect the DC power supply to the DC input power source.
-
Page 12: Dc Power Supply Specifications
Figure 3: DC power supply The 800 W DC power supply uses a DC power supply wiring assembly to connect the power supply to the DC power source. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400... - Page 13 Series. The illustrations show the VSP 8200 as an example, but the instructions apply to any switch in the series. There are three ways to install the VSP 8400 in an equipment rack. Refer to one of the following sections: •...
- Page 14 2. Use the following steps to detach the chassis rail from the slide’s rack rail: a. Pull the inner chassis rail and slide it out as far as you can. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 15 Slide the white release lock in the direction of the arrow stamped on the lock. 3. Lift the locking mechanism on the rack rail to slide the outer section back into the main section. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 16 Orient the chassis rail with the blue release lock towards the front and position the rail over the standoffs on the chassis. b. Slide the chassis rail to the rear until the rail locks into the standoffs. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 17 Adjust the length of the rack rail so it fits the rack depth by loosening the two screws on the rack rail, adjusting the length, and then tightening the screws. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 18 Push the end of the front bracket assembly so it opens up. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 19 Insert the bracket pins into the desired holes in the frame. e. Close the bracket assembly so that it wraps around the frame and locks into place. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 20 6. Use the following steps to install the switch in the equipment rack to complete the installation: a. Insert the chassis rails on the switch into the rack rails on the frame. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 21 To slide the switch back into the rack, push the blue locks on the chassis rails towards the back and slide the switch into the frame. 7. Connect power and network connections to the switch. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 22 5. Remove the two screws and nuts securing the short rear bracket to the rack rail. This bracket is for 300mm-600mm equipment racks only and is not used in this installation. Save the bracket for possible future use. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 23 Lift the locking mechanism and slowly slide the rail back into the main assembly. This exposes a “window” over the screw holes so you can install the remaining three screws one at a time. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 24 Push the end of the front bracket assembly so it opens up. c. Insert the bracket pins into the desired holes in the frame. d. Close the bracket assembly so that it wraps around the frame and locks into place. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 25 To slide the switch back into the rack, push the blue locks on the chassis rails towards the back and slide the switch into the frame. 10. Connect power and network connections to the switch. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 26 • 900mm equipment rack that weighs less than 14kg • 600mm equipment rack that weighs less than 21kg • 300mm equipment rack that weighs less than 42kg June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 27 Follow these steps if you have to remove the switch from an equipment rack. Important: This procedure requires two people. Procedure 1. Disconnect the power cord from the switch. 2. Slide the switch out until the lock engages. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 28 3. While the person standing in back of the chassis slides both of the white release locks (one on each side of the chassis) towards the front, the person standing in front of the chassis pulls the chassis out of the rack. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 29 The chassis weight will cause damage to a rack when mounted by the front panel, especially in an environment with vibration or in an earthquake prone area. Procedure 1. Disconnect the power cord from the switch. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 30 2–post rack, attach the bracket in the location recessed 150 mm from the front of the chassis. 3. Slide the switch onto a shelf or tray in the rack. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...
- Page 31 4. Insert and tighten the rack-mount screws. 5. Verify that the switch is securely fastened to the rack. 6. Connect power and network connections to the switch. June 2015 Installation Job Aid for Avaya Virtual Services Platform 8400...