Haier IT9001 Service Manual
  1. Manuals
  2. Brands
  3. Haier Manuals
  4. Ventilation Hood
  5. IT9001
  6. Service manual

Haier IT9001 Service Manual

Hide thumbs Also See for IT9001:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual

Advertisement

Table of Contents
loading

Related Manuals for Haier IT9001

Summary of Contents for Haier IT9001

  • Page 1 Service Manual...

  • Page 2: Cooker Hood

    IT9001 Cooker Hood INSTALLATION AND USER’S MANUAL...

  • Page 3: Safety Precaution

    SAFETY PRECAUTION • mportant! Always switch off the electricity supply at the mains during installation and maintenance such as light bulb replacement. • he cooker hood must be installed in accordance with the installation instructions and all measurements followed. • ll installation work must be carried out by a competent person or qualified electrician.

  • Page 4: Maintenance

    SAFETY PRECAUTION • aution: The appliance and its accessible parts can become hot during operation. Be careful to avoid touching the heating elements. Children younger than 8 years old should stay away unless they are under permanent supervision. – here shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels.

  • Page 5: Parts Identification

    (7) Washer (2 pcs) (8) Wall plug (8 pcs) (9) ø 4mm x 35mm Screw (8 pcs) (10) Exhaust hose (ø15cm) (11) Carbon filter (required for circulating air mode) (12) Cable tie Technical specifications Model CXW-200-IT9001 Voltage 220-240V~50Hz Product dimension 90x49x55 WxDxH(in cms)
  • Page 6 Wattage(Total) 202W Motor 200W Filter 1xAluminium Filter Light 1x2W LED lights Noise Level 68dB Speed control 2 Speed control Type of switch Electronic switchl...

  • Page 7: Installation

    Installation (for venting outside) When the cooker hood is to be installed above an electric hob or a gas hob, the minimum distance between the hob and cooker hood must exceed 700mm. If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account.
  • Page 8 Drill holes for mounting the body. Fix support plate on the wall by screws with expanding plugs. 10mm Fig. 8 Fig. 7 Secure hood (tighten all screws). Fit ducting adaptor. Fig. 9 Fig. 10 IMPORTANT SAFETY WARNING: ONLY USE THE SCREWS PROVIDED WITH THE RANGE HOOD TO MOUNT THE DUCTING ADAPTOR.
  • Page 10 If you do not have an outlet for exhausting air, the exhaust hose (part [10]) is not required, and the installation is similar to the one shown in the section "Installation (for venting outside)". Air is vented back into the kitchen through the opening of the cooker hood, this circulating air mode requires the use of the carbon filter (part [11]) to remove odors.

  • Page 11: Using Your Cooker Hood

    Using your Cooker hood For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. Fig. 13 ON/OFF Key/Delay Timer: • Press the key to turn on/o the extractor.

  • Page 12: Care And Maintenance

    Care and Maintenance IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE COOKER HOOD WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean your cooker hood effectively by simply using a dilute solution of water and mild detergent and then dry it with a clean cloth.
  • Page 14 Information for cooker hood ENVIRONMENTAL PROTECTION: This product is marked with the symbol on the selective sorting of waste electronic equipment. This means that this product must not be disposed of with household waste but must be supported by a system of selective collection in accordance with Directive 2002/96/EC.

  • Page 15: Troubleshooting

    Troubleshooting Failure Root cause Corrective action 1. Not plug-in or poor plug- 1. Plug-in perfect. power 2. Connect with power supply or 2. Power socket is no contact electrician for after power. service. 3. Power supply dose not 3. Replace fuse or call connect with fuse or fuse electrician for after service.
  • Page 16 1. Oil cup. Remove oil cup from card slot based on horizontal. 2. Filter Remove screws to take out filter. 3. Hand-fasten nut Clockwise rotate the nut to remove it. 4. Fan...
  • Page 17 Remove fan. 5. Chimney Remove 4 screws, take out chimneys. 6. Cover sheet...
  • Page 18 Remove 4 screws to take out cover sheet. 7. Maintainence cover Remove 12 screws to take out maintainence cover. Then repair fan and motor. 8. Remove 8 screws from damper and 4 screws from air outlet. Then from reverse side of body to remove one M5 screw.
  • Page 19 9. LED light and switch control wire Use flat screwdriver to remove LED light. Disconnect all responding wire connectors for replacement.
  • Page 20 Wiring Diagram...

Table of Contents