Advertisement
Quick Links
BEALE
™
ELECTRONIC PULL-DOWN
KITCHEN FAUCET
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
(A) Installation on 1-hole mounting surface: (please refer to template provided)
• Make certain the SEAL (2) is properly seated in bottom recess of MOUNTING RING (10) and SEAL (13) in top recess of
MOUNTING RING (10). Place mounting ring over mounting hole at the deck. Insert CABLES (12), HOSES (3) and SHANK (4)
through mounting ring and deck, seat SPOUT BASE onto sink or mounting surface. Do not use putty.
• From below: Insert CABLES (12) and HOSES (3) through RUBBER WASHER (6), BRASS WASHER (7), and threaded
LOCKNUT (8).
• Assemble RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8) onto SHANK (5) from underside
of sink or mounting surface. Hand tighten LOCKNUT (8).
• Make sure faucet is aligned properly with handle on the right and logo facing directly forward.
• Use a screwdriver to tighten SCREWS (9) on LOCKNUT (8). Work your way around LOCKNUT (8), tightening the screws
slightly each time until all are snug to ensure even pressure.
(B) Optional: Installation on 3-hole mounting surface: Requires Deck Escutcheon - order separately
• Make certain the SEAL (13) is properly seated in top recess of DECK ESCUTCHEON (1) and FOAM SEAL (14) is properly
seated in bottom recess of DECK ESCUTCHEON (1). Do not use putty. (Please refer to the template provided)
• Screw in two THREAD RODS (15) onto bottom of DECK ESCUTCHEON (1).
• Place deck escutcheon over mounting holes of the deck.
• Insert SUPPLY CABLES (12), HOSES (3), SPRAY HOSE (4) and SHANK (5) through hole of DECK ESCUTCHEON (1) and
mounting surface.
• Follow mounting instructions above
to secure faucet to mounting surface.
Thread the MOUNTING NUTS (11) to
secure DECK ESCUTCHEON.
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
INSTALLATION
INSTRUCTIONS
Flat Blade Screwdriver
A
13
10
SPOUT BASE
2
4931380
4931385
Phillips Screwdriver
CAUTION
13
10
2
12
5
3
SINK OR
MOUNTING
4
SURFACE
6
7
8
9
- 1 -
Certified to comply with ANSI A112.18.1M
Adjustable Wrench
Turn off water at
main supply
B (OPTIONAL)
13
SPOUT BASE
15
5
3
11
4
6
7
8
9
M965686 Rev. 1.9 (1/19)
1
14
Advertisement
Related Manuals for American Standard Beale 4931385
Summary of Contents for American Standard Beale 4931385
- Page 1 4931380 ELECTRONIC PULL-DOWN 4931385 KITCHEN FAUCET Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M...
- Page 2 MAKE WATER SUPPLY CONNECTIONS • Turn off hot and cold water supplies before beginning. • Place each SCREEN FILTER (3) on each wall supply outlet. Be sure that SCREEN FILTER (3) is inserted in the correct direction. (See Illustration) (3) SCREEN FILTER •...
- Page 3 ELECTRICAL CONNECTIONS - SENSOR TO SOLENOID • Connect SOLENOID CONNECTOR (12) with the sensor connector from the faucet with the yellow tag stickers, secure this connection by installing inside the CONNECTORS HOUSING (3) as shown and lock by twisting the white end pieces.
- Page 4 CHECK CONNECTIONS FOR LEAKS • Move HANDLE (1) into “off” position. • Turn on water supplies and check connections for leaks. • Operate HANDLE (2) up and down, left and right to flush water lines thoroughly. • Operate HAND SPRAY and check connections for leaks. CHECK CONNECTIONS FOR LEAKS TEST INSTALLED FAUCET...
-
Page 5: Spray Operation
SPRAY OPERATION • With FAUCET on, press TOGGLE BUTTON (4) on SPRAY (3) to switch from stream to spray. • Press and hold PAUSE BUTTON (5) to temporarily stop flow from SPRAY (3). Release PAUSE BUTTON (5) to resume flow from SPRAY (3). STREAM (AERATOR) SPRAY SERVICE... - Page 6 BEALE ™ ELECTRONIC PULL-DOWN KITCHEN FAUCET MODEL NUMBER 4931380 Replace the “YYY” with 4931385 appropriate finish code POLISHED CHROME STAINLESS STEEL M951483-0070A M964450-YYY0A CARTRIDGE SPRAY WITH HOSE M918511-0070A CARTRIDGE SCREWS M907315-YYY0A M970209-0070A ESCUTCHEON CAP AERATOR M922372-0070A AERATOR KEY M964453-YYY0A HANDLE KIT M964452-YYY0A MOUNTING RING M970620-0070A...