Adjusting The Position Of An Existing Start Id; Erasing Start Ids - Sony DTC-ZE700 Operating Instructions Manual

Accurate Positioning of Start IDs
(Rehearsal)
1
During playback, press START ID REHEARSAL
when you arrive at the proper position.
"REHRSL" appears, "START ID" flashes in the
display and Rehearsal repeats a 3-second portion
starting from the selected position. Note that the
repeated portion will play back 8 times, with the
remaining number of times appearing to the right
of the "REHRSL". After 8 times, the deck
automatically stops.
2
Press 0 or ) to move the beginning of the
repeated portion.
Each time you press the 0 or ) button, the
beginning of the repeated portion shifts
backwards or forwards in 0.3-second increments,
up to a maximum extent of about 2 seconds (4
seconds in long-play mode) in either direction.
Position where the START
ID REHEARSAL button is
pressed in step 1.
3 seconds
0.3 sec
Movement with each
0.3 sec
press of 0
The time in the display shows the shift in position
from the time the START ID REHEARSAL button
was pressed.
After pressing
) twice
0 6 .
S
START ID
3
Press START ID WRITE.
"ID WRITE" appears in the display for a few
seconds and the start ID is written on the tape at
the selected position. "START ID" flashes in the
display during this time.
Repeated portion
Movement with each press of )
After pressing
0 twice
0 6 . S
START ID
Writing Sub Codes
Adjusting the Position of an
Existing Start ID
You can adjust the position of previously recorded
start IDs.
MODE
RESET
g TIMER START ID MARGIN
REC OFF PLAY AUTO RENUMBER REHEARSAL WRITE ERASE RESET
POWER
START ID REHEARSAL
1
During playback, press START ID REHEARSAL
when the existing start ID you want to reposition
is displayed.
The deck rewinds to the beginning of start ID and
Rehearsal repeats a 3-second portion is displayed.
2
Do steps 1 to 3 of "Accurate Positioning of Start
IDs (Rehearsal)" on this page.
You can move the start ID to a maximum extent of
about 2 seconds (4 seconds in long-play mode) in
either direction from its original position.
Note
Start IDs written within 10 seconds from the end of the tape
may be difficult or impossible to move.

Erasing Start IDs

You can erase any start ID.
MODE
RESET
g TIMER START ID MARGIN
REC OFF PLAY AUTO RENUMBER REHEARSAL WRITE ERASE RESET
POWER
START ID ERASE
Press START ID ERASE when the start ID you want to
erase is displayed.
"(ERASE)" appears in the display as the deck rewinds
to the beginning of the start ID, then "ID ERASE"
appears as the deck erases the start ID.
• It takes 9 seconds to erase a start ID.
• Program numbers are erased together with start IDs.
REC LEVEL L R
INPUT REC MODE SBM
5
OPEN/CLOSE STANDARD ON 4 6
ANALOG 48 kHz
3 7
§
OPTICAL 44.1 kHz
COAXIAL LONG
2 8
OFF
1 9
AMS REC MUTE
≠ ± 0 ) R 0 10
PHONES PHONE LEVEL
p · P r
REC
0 10
REC LEVEL L R
INPUT REC MODE SBM
5
STANDARD ON 4 6
OPEN/CLOSE
ANALOG 48 kHz
§ 3 7
OPTICAL 44.1 kHz
COAXIAL LONG
2 8
OFF
1 9
AMS REC MUTE
≠ ± 0 ) R
0 10
PHONES PHONE LEVEL
p · P r
REC
0 10
17 EN