Advanced Remote Operations; Operating One Component While Using Another (Background Operation); Changing The Factory Setting Of A Function Button - Sony TA-VA80ES Operating Instructions Manual

Advanced Remote Operations

Operating One Component
While Using Another
(background operation)
You can temporarily operate other components while
listening to or watching a program.
SLEEP
LEARN
SYSTEM CONTROL / FUNCTION
VIDEO 1 VIDEO 2 VIDEO 3
(AUTO CATEGORIZE SYSTEM)
TAPE DAT/MD
TV
CONTROL
1
ON
4
7
BACK
GROUND
BACKGROUND SHIFT
>
10
+
– SUB CH POSITION
0 ) =
— RMS —
DIRECTION CLEAR
9 (
— SOUND FIELD —
ON/OFF GENRE MODE
EQ/
TONE BAND SLOPE
DIGTAL DIRECT
PROCESSING
CONTROL
DPC
MODE
PROGRAMMABLE
1
Hold down BACKGROUND.
2
Press both the corresponding button of the
component you're going to use (see the table
below) and one of the following buttons at the
same time; VISUAL POWER, TV/VIDEO, CH/
PRESET +/–, ANT TV/VTR, D.SKIP, (, 9, p,
0/), =/+, P, r.
Example: To start recording on a tape deck
while listening to a CD
While holding down BACKGROUND,
press 4 (or 5) and press r + ( at the
same time.
The following buttons correspond to the
components.
The button Corresponds to
1 CD player
2 DAT deck
3 MD deck
4 Tape deck A
5 Tape deck B
6 LD player
7 VCR (remote control mode VTR 1
8 VCR (remote control mode VTR 2
9 VCR (remote control mode VTR 3
>10 DBS (Digital Broadcasting System)
tuner
*
Sony VCRs are operated with a VTR 1, 2 or 3 setting
that corresponds to Beta, 8mm, and VHS,
respectively.
SYSTEM OFF
VISUAL
POWER
LD TV
CD TUNER PHONO
5.1
INPUT
2 3
TV/VIDEO
5 6
Numeric
D.TUNING
DISC
8 9 +
buttons
CH/
PRESET
ENTER
0 –
RMS/START
ANT
SWAP TV/VTR
+
D. SKIP
P IN P JUMP
p P r
TEST
TONE
— LEVEL —
+ +
REAR CENTER
– –
MASTER
BASS
VOL
BOOST
MUTING
*
)
*
)
*
)
Advanced Remote Operations
Changing the Factory Setting
of a FUNCTION Button
If the factory settings of the SYSTEM CONTROL/
FUNCTION buttons (page 12) don't match your
system components, you can change them. For
example, if you connect a Sony LD player to the
VIDEO 2 jacks, you can assign the VIDEO 2 button to
set the remote to control the LD player.
Note that the settings of the TUNER and PHONO
buttons cannot be changed.
SLEEP LEARN
SYSTEM CONTROL / FUNCTION
VIDEO 1 VIDEO 2 VIDEO 3
(AUTO CATEGORIZE SYSTEM)
TAPE DAT/MD CD
TV
CONTROL
1 2
ON
4 5
Numeric
7 8
buttons
BACK
GROUND SHIFT
0
>
10
– +
SUB CH POSITION
0 ) =
— RMS —
DIRECTION CLEAR
9 ( p
— SOUND FIELD —
ON/OFF GENRE MODE
EQ/
TONE BAND SLOPE
DIGTAL
DIRECT
PROCESSING
CONTROL
DPC
MODE
PROGRAMMABLE
1
Hold down the SYSTEM CONTROL/FUNCTION
button whose function you want to change
(VIDEO 2, for example).
2
Press the corresponding numeric button of the
component you want to assign to the SYSTEM
CONTROL/FUNCTION button (6 - LD player,
for example).
For the numeric buttons, see the table in
"Operating One Component While Using
Another" on this page.
Now you can use the VIDEO 2 button to control
your Sony LD player.
To reset the setting to the factory setting
Repeat the above procedure.
Getting Started
SYSTEM OFF
VISUAL
POWER
SYSTEM
LD TV
TUNER PHONO
CONTROL/
5.1
INPUT
3
FUNCTION
TV/VIDEO
6
D.TUNING
DISC
9 +
CH/
ENTER PRESET
–
RMS/START
ANT
SWAP TV/VTR
+
D. SKIP
P IN P JUMP
P r
TEST
TONE
— LEVEL —
+ +
REAR CENTER
– –
MASTER
BASS
VOL
BOOST
MUTING
EN
23