Table of Contents
Advertisement
Menu List
This section describes the menus displayed as you turn
the jog dial. The setting surrounded by
indicates the factory setting.
Item
Function
AGC
To adjust the
input signal to the
optimum printing
level
a)
ASPCT
To select the
aspect ratio
BEEP
To turn operation
tones ON and
OFF. Error tones
sound regardless
of setting.
CLEAN
To start head
cleaning
CLEAR
To delete images
stored in memory.
.
AT
CUT
To turn on and off
(UP-990AD
automatic cutting
only function)
of completed
prints.
b)
DIR
To select whether
the top or bottom
of the screen is to
be printed first
16
Adjustments and Settings Using the Menu
Settings
AG:ON: Adjusts the input
signal to the optimum level,
when the printout image
appears too dark or too
light.
[AG:OFF]: Normally select
this setting.
BACK: Cancels the setting
change and returns to the
item selection column.
AS:1:1: Prints a video
signal with an aspect ratio
of 1:1.
[AS: 4:3]: Normally select
this setting.
BACK: Cancels the setting
change and returns to the
item selection column
BE: OFF: The operation
tone does not sound.
[BE: ON]: The operation
sounds.
BACK: Cancels the setting
change and returns to the
item selection column.
[CLN: OK]: Starts the head
cleaning. Be sure to use the
supplied cleaning sheet.
BACK: Cancels the head
cleaning and returns to the
item selection column.
[CLR: OK]: Deletes all
images stored in memory.
BACK: Cancels CLEAR
and returns to the item
selection column.
CT:OFF: Cuts the paper
when the CUT button is
pressed.
[CT:ON]: Cuts the paper
automatically.
BACK: Cancels the setting
change and returns to the
item selection column.
DI: REV: Starts to print in
the reverse direction (from
the top of the screen).
[DI: NOR]: Starts to print in
the normal direction (from
the bottom of the screen).
BACK: Cancels the setting
change and returns to the
item selection column.
Item
Function
FEED
To set the top and
(UP-990AD)
bottom margin of
a print.
FEED
To select the
(UP-970AD)
paper feed
method used after
printing.
FRAME
To select the
color of the frame
between images
in multi-picture
mode.
GAMMA
To select the tone
of the printouts
(density
gradation)
IMAGE
To set the printout
to either positive
printout or
negative printout
INFO
To select whether
or not the print
conditions (such
as contrast,
bright, gammas
and sharpness
information) are
printed under the
image
Settings
[FE: 0]to FE:15: Sets the
margin to one of 16 steps
from 0 to 15. An increase of
one step increases the top
and bottom margin by 5
mm. The top and bottom
margin can be increased to
75 mm. The "0" setting is
the default value, which
still provides a narrow
margin between two
images.
BACK: Cancels the setting
change and returns to the
item selection column.
[FE: ON]: Increases the
margin between prints.
FE:OFF: Sets when
reducing the margin or
when printing multiple
images on the same sheet.
This reduces the margin
between images allowing
you to print more images
per roll. However, with this
setting, the FEED button
must be pressed before
cutting the paper.
BACK: Cancels the setting
change and returns to the
item selection column.
FR:BLK: Sets the frame
color to black.
[FR:WHT]: Sets the frame
color to white.
BACK: Cancels the setting
change and returns to the
item selection column.
GA:3: TONE 3 Hard
gradation
GA:2: TONE 2 Soft
[GA:1]: TONE 1 Standard
gradation
BACK: Cancels the setting
change and returns to the
item selection column.
IM:NEG: Makes negative
printouts.
[IM:POS]: Makes normal
printouts.
BACK: Cancels the setting
change and returns to the
item selection column.
IF:ON: Prints the
information.
[IF:OFF]: Does not print the
information.
BACK: Cancels the setting
change and returns to the
item selection column.
Hide quick links:
Advertisement
Table of Contents
