Related Manuals for IBM 5147-084
Summary of Contents for IBM 5147-084
- Page 1 IBM ESS expansion Version 5.1 Installation and User Guide - Model SC27-4628-01...
- Page 2 The information in the “Safety and environmental notices” on page ix v The information in the IBM Environmental Notices and User Guide (provided on a DVD) This edition applies to IBM ESS expansion Model 084 and is valid until replaced by new editions. © Copyright IBM Corporation 2017.
-
Page 3: Table Of Contents
. 29 Russia Electromagnetic Interference Class A LEDs . 29 Statement . . 63 Thermal sensors . . 35 Homologation statement . . 63 Troubleshooting . . 35 Dealing with hardware faults . . 36 © Copyright IBM Corp. 2017... - Page 4 Installation and User Guide - Model 084...
-
Page 5: Figures
. 46 Ops panel LEDs . . 26 Removing a module (1). (6Gb/s SAS EBOD Anti-tamper locks . 28 module shown) . . 47 PSU LEDs . . 30 Removing an I/O module (2) . 47 © Copyright IBM Corp. 2017... - Page 6 Installation and User Guide - Model 084...
-
Page 7: Tables
6Gb/s SAS EBOD I/O Module LED Supported drives for enclosure . . 51 Descriptions . . 34 Shock and vibration tolerance . . 51 Alarm Conditions . 35 Power cord specifications . . 56 Enclosure dimensions . . 49 © Copyright IBM Corp. 2017... - Page 8 viii Installation and User Guide - Model 084...
-
Page 9: Safety And Environmental Notices
Safety and environmental notices Review the safety notices, environmental notices, and electronic emission notices for IBM ESS expansion (5147-106) before you install and use the product. Suitability for telecommunication environment: This product is not intended to connect directly or indirectly by any means whatsoever to interfaces of public telecommunications networks. - Page 10 Familiarize yourself with the IBM Safety Notices publication G229-9054, which is included with your product. DANGER When working on or around the system, observe the following precautions: Electrical voltage and current from power, telephone, and communication cables are hazardous. To avoid a shock hazard: ®...
- Page 11 DANGER Heavy equipment—personal injury or equipment damage might result if mishandled. (D006) DANGER Professional movers are to be used for all relocation activities. Serious injury or death may occur if systems are handled and moved incorrectly. (D008) DANGER Serious injury or death can occur if loaded lift tool falls over or if a heavy load falls off the lift tool.
- Page 12 (R001 part 2 of 2): CAUTION: v Do not install a unit in a rack where the internal rack ambient temperatures will exceed the manufacturer's recommended ambient temperature for all your rack-mounted devices. v Do not install a unit in a rack where the air flow is compromised. Ensure that air flow is not blocked or reduced on any side, front, or back of a unit used for air flow through the unit.
- Page 13 CAUTION: High levels of acoustical noise are (or could be under certain circumstances) present. Use approved hearing protection and/ or provide mitigation or limit exposure. (L018) xiii Safety and environmental notices...
-
Page 14: Environmental Notices
Environmental notices This information contains all of the required environmental notices for IBM Systems products in English and other languages. The IBM Systems Environmental Notices information includes statements on limitations, product information, product recycling and disposal, flat panel display, refrigeration and water-cooling systems, external power supplies, and safety data sheets. -
Page 15: Support Information
Support information Your location Method of contacting the IBM Support Center In the United States Call 1-800-IBM-SERV for support. Outside the United States Contact your local IBM Support Center or see the Directory of worldwide contacts. © Copyright IBM Corp. 2017... - Page 16 Installation and User Guide - Model 084...
-
Page 17: Chapter 1. Appliance Safety Precautions
A fully configured enclosure weighs up to 135kg (298lb). An unpopulated enclosure weighs 46kg (101lb). Use appropriate lifting methods. The packaging includes lifting straps wrapped and buckled around the enclosure. Ensure the lifting straps buckle is properly closed, and lift with the loops attached to the lifting straps. © Copyright IBM Corp. 2017... -
Page 18: Chassis Label (Fcc Compliance)
CAUTION: The weight of this part or unit is more than 55 kg (121.2 lb). It takes specially trained persons, a lifting device, or both to safely lift this part or unit. (C011) The following artwork might be only a draft. The use of certification marks on a product must be authorized by the respective National Certification Bodies (NCBs) that own the marks. -
Page 19: Operation
v Unplug all cords and cables from the enclosure. v Remove all DDIC modules from both drawers and make sure the drawers are closed firmly and locked shut. See "Locking drawers." Use a minimum of three people to lift the enclosure. CAUTION: A fully configured enclosure weighs up to 135kg (298lb). - Page 20 CAUTION: A hot surface nearby. (L007) Installation and User Guide - Model 084...
-
Page 21: Electrical Safety
Figure 3. Compliance label with safety warning label CAUTION: Before removing a PSU module, disconnect the power cord from that module. Otherwise, modules at the rear of the enclosure are hot-swappable. Do not use open drawers to support any other equipment. Figure 4. - Page 22 Important: The enclosure must be grounded before applying power. The plug on the power supply cord is used as the main disconnect device. Ensure that the socket outlets are located near the equipment and are easily accessible. CAUTION: When powered by multiple AC sources, unplug all power supplies to ensure disconnection. DANGER Do not remove covers from the enclosure or any of the modules.
-
Page 23: Rack System Safety Precautions
DANGER HIGH LEAKAGE CURRENT. Earth connection essential before connecting supply. CAUTION: The PSUs contain double pole/neutral fusing. Ensure that your electrical installation can support this type of fusing. Important: If the enclosure is equipped with I/O modules having an RJ45 socket, that socket is for Ethernet connection only and must not be connected to a telecommunications network. -
Page 24: Electrostatic Discharge (Esd) Precautions
DANGER: Rack-mounted devices are not to be used as shelves or work spaces. (L002) CAUTION: Do not pull out more than one drawer at a time. The rack might become unstable if you pull out more than one drawer at a time. (L024) Electrostatic discharge (ESD) precautions Fit and check a suitable anti-static wrist or ankle strap and observe all conventional ESD precautions when handling plug-in modules and components. -
Page 25: Chapter 2. System Overview
This enclosure is designed for high availability, with no single point of failure for data or power. It complies to the Storage Bridge Bay (SBB) v2.0 specification, which specifies interconnects, power budgets, power rails, mechanical and thermal form factors and footprints. © Copyright IBM Corp. 2017... -
Page 26: The Enclosure Core Product
Figure 6. Enclosure: rear view The enclosure core product The IBM ESS expansion design concept is based on an enclosure subsystem together with a set of plug-in modules. A typical enclosure system for direct dock comprises: v An enclosure chassis comprising the following parts: –... -
Page 27: Enclosure Chassis
Important: To ensure correct airflow and cooling, all PSU bays and cooling module bays must contain a functioning unit. If the enclosure is run with a single SBB I/O module, the other I/O module bay must be filled with a blank module. Each row of drive bays must be completely empty or completely full. Figure 7. -
Page 28: Disk Drives In Carriers (Ddics)
v The drawer locks into place when opened all the way. To reduce pinching hazards, two latches must be released before the drawer can be pushed back in. Power and data are sent via three baseplanes and two sideplanes. Each drawer can be locked shut by turning both anti-tamper locks clockwise using a screwdriver with a Torx T20 bit (see Figure 7 on page 11). - Page 29 v SAS carrier transition card. Figure 9. A disk drive in carrier (DDIC) The following hard disk drives are supported: v 3.5” 7200rpm SAS drive The following solid state drives are supported: v 2.5” SAS solid state drive with 3.5” adapter Note: SSD drives are supported only for logtip backup.
- Page 30 Operator’s panel The front of the enclosure features an operator’s (ops) panel (shown in Figure 2–6) on the left-hand side which contains the following: v Unit Identification Display. v Mute/Input button. v Power On/Standby LED (green/amber). v Module Fault LED (amber). v Logical Status LED (amber).
-
Page 31: Power Supply Unit (Psu)
Power On/Standby LED (green/amber) Shows amber when the system is in standby (not operational). Shows green when the system is on (operational). Module Fault LED (amber) Shows amber when there is a system hardware fault. Additionally, an LED may be lit on a PSU, drawer, DDIC, cooling module, or I/O module that helps you identify which component is at fault. -
Page 32: Cooling Module
The back of the PSU has a power switch, three status LEDs and a socket for the power cord, as shown in the following figure. Figure 12. PSU LEDs Cooling module The five cooling modules at the rear of the enclosure maintain all system components below their maximum temperature, assuming the ambient temperature is below 95°... -
Page 33: Sbb I/O Module
Figure 13. Cooling module System airflow The system must be operated with low pressure rear exhaust installation. Back pressure created by the rack doors and obstacles is not to exceed 5 pascals (0.5mm water gauge). The cooling system provides sufficient capacity to ensure that maximum temperatures are not exceeded. The minimum open area for the rack doors is 70%. -
Page 34: Enclosure Management
Figure 14. 6Gb/s SAS EBOD module The system can operate with one or two modules. If the enclosure is run with a single module, the other I/O module bay must be filled with a blank module. The presence of I/O modules is checked when the power is switched on. -
Page 35: Chapter 3. Installation
2. Inspect the packaging for crushes, cuts, water damage or any other evidence of mishandling during transit. If there is any damage, photograph the packaging for future reference before opening. 3. Remove the packaging, as shown in the following figure. © Copyright IBM Corp. 2017... -
Page 36: Installation
Figure 15. Unpacking the system Installation First, install the rail kit, then install the modules. Installing the rail kit CAUTION: An unpopulated enclosure can weigh up to 46kg (101lb). Do not try to lift it by yourself. Due to the weight of the enclosure, install it without the drive carriers. The adjustment range of the rail kit, from the inside of the front post to the inside of the rear post is 660mm - 840mm. -
Page 37: Mounting The System Into A Rack (Left Rail Only)
1. To facilitate access, remove the door from the rack. 2. Ensure the pre-assembled rails are at their shortest length. 3. Locate the rail location pins inside the front of the rack and extend the length of the rail assembly to enable the rear location pins to locate. -
Page 38: Power Cord Connection
Figure 17. Rear enclosure mounting 3. The sliding nut head must always face away from the enclosure, whichever configuration is used. CAUTION: Use only the power cords supplied or cords that match the specification in Appendix B, "AC power cords." CAUTION: After the enclosure is installed in the rack, dispose of the lifting straps. -
Page 39: Grounding Checks
Important: When more than one PSU is fitted, connect each PSU to separate and independent supplies to guarantee redundancy. CAUTION: Always remove the power connections before you remove the PSU from the enclosure. DANGER: Multiple power cords. The product might be equipped with multiple power cords. To remove all hazardous voltages, disconnect all power cords. - Page 40 v All the supplied plug-in modules must be in place for the air to flow correctly around the enclosure and also to complete the internal circuitry. Each row of drive bays must be completely empty or completely full. v If the enclosure system is used with modules missing for more than a few minutes, the enclosure can overheat, causing power failure and data loss.
-
Page 41: Chapter 4. Operation
Allow 15 seconds between turning the PSU off and back on again. v Allow 15 seconds between turning one PSU in the system on and the other PSU off. v Never turn off a PSU whilst any amber LED is lit on the partner PSU. © Copyright IBM Corp. 2017... -
Page 42: Ops Panel Leds
Ops panel LEDs Ops panel LEDs indicate fault and status conditions. The following table shows the possible conditions for the LEDs. Table 1. Ops panel LEDs Power On/Standby Constant green: power is on Constant amber: system is in standby (not operational) Module Fault Constant or flashing amber: fault Logical Status... -
Page 43: Normal Power Down
4. Shut down the enclosure by switching off all the power swtiches of the installed PSUs. When the enclosure has to be powered down to perform service actions, follow the instructions provided by IBM service. Locking drawers A drawer can be locked shut by using a screwdriver with a Torx T20 bit to rotate both anti-tamper locks until the red arrows point away from the center of the enclosure. -
Page 44: Anti-Tamper Locks
Figure 20. Anti-tamper locks Installation and User Guide - Model 084... -
Page 45: Chapter 5. Troubleshooting
Elastic Storage Server Appendix of Elastic Storage Server Deploying the Elastic Storage Server Guide. ™ See subsection Disk Enclosure and HBA cabling in chapter Setting up IBM Spectrum Scale RAID in the Elastic Storage Server Spectrum Scale RAID Administration Guide. -
Page 46: Psu Leds
PSU LEDs Figure 21. PSU LEDs Table 2. PSU LED states AC Missing PSU Fail (Amber) (Amber) Power (Green) Status No AC power to either PSU. PSU present, but not supplying power or PSU alert state (usually due to critical temperature). Main AC present, switch on. -
Page 47: Cooling Module Leds
Cooling module LEDs Figure 22. Cooling module LEDs Table 3. Cooling module LED descriptions Description Module OK Constant green indicates that the fan is working correctly. Off means the fan has failed. Follow the procedure in "Replacing a Cooling Module." Battery Fault Not currently used. -
Page 48: Operator's Panel Leds
Figure 23. Operator’s panel LEDs Table 4. Ops panel LED descriptions Display/LED Description Unit Identification Display Usually shows the identification number for the enclosure, but can be used for other purposes. Power On/Standby LED Amber if the system is in standby. Green if the system has full power. -
Page 49: Drawer Leds (Left Sideplane Only)
Drawer LEDs The following figure shows the names and locations of the disk drawer LEDs. Figure 24. Drawer LEDs (left sideplane only) Table 5. Drawer LED descriptions Description Sideplane OK/Power Good Green if the sideplane card is working and there are no power problems. Drawer Fault Amber if a drawer component has failed. -
Page 50: Drive Fault Led
Figure 25. Drive Fault LED SBB I/O Module LEDs The following figure shows the LEDs on the 6 Gb/s SAS EBOD SBB I/O module. Figure 26. SBB I/O module LEDs Table 6. 6Gb/s SAS EBOD I/O Module LED Descriptions Description I/O Module OK Constant green if the I/O module is operating correctly. -
Page 51: Thermal Sensors
Thermal sensors Thermal sensors throughout the enclosure and its components monitor the thermal health of the storage system. Exceeding the limits of critical values will cause the Over-temperature alarm to occur. Troubleshooting The following sections describe problems that can occur with your storage systems and some possible solutions. -
Page 52: Dealing With Hardware Faults
Ensure that you have obtained a replacement module of the same type before removing any faulty module. Important: Only replace a module when it has been instructed by IBM service. Unplanned replacement of modules can lead to loss or access of data. When a module is removed for service, replace it immediately. -
Page 53: Chapter 6. Module Replacement
The drawer sideplanes can be hot-swapped in the field. Replacement of the sideplanes requires a special tool and should be carried out by service personnel only. Refer to the IBM ESS Expansion Hot Swap Side Card - Quick Installation Guide for full instructions. -
Page 54: Anti-Tamper Locks (Shown Disengaged)
Opening a drawer 1. Make sure the anti-tamper locks are not engaged. The red arrows on the locks will point inwards if the locks are disengaged (see the following figure). Unlock them if necessary by rotating them counterclockwise using a screwdriver with a Torx T20 bit. Figure 27. -
Page 55: Replacing A Disk Drive In Carrier (Ddic)
Closing a drawer 1. Press and hold both of the black latches on the sides of the drawer (see the following figure). Figure 29. Drawer latch 2. Push the drawer in slightly. 3. Release the black latches and check they have returned to their original position. 4. -
Page 56: Drive Location Plan
Figure 30. Drive location plan Note: Some enclosure management features identify drive bays using a 1-based count (1–84) while others use a 0-based count (0–83). For more information, contact the storage provider. 2. Open the relevant drawer using the instructions in "Opening a Drawer." 3. -
Page 57: Removing A Ddic
Figure 31. Removing a DDIC 5. Pull the drive upward and out of the drawer. Important: If you are not going to replace the drive immediately, close the drawer (see "Closing a Drawer") so that correct airflow and cooling are maintained in the enclosure. Inserting a DDIC Important: Failed drives must be replaced with approved drives. -
Page 58: Replacing A Cooling Module
Figure 33. Latch position of a correctly inserted drive 5. Close the drawer using the instructions in section Closing a Drawer. Note: The drawers must be populated with drives in whole rows at a time (there are 3 rows of 14 drives per drawer). -
Page 59: Cooling Module Leds
Figure 34. Cooling module LEDs 2. As shown in the following two figures, push down and hold the red release latch (1) and pull the module out by its handle (2). Figure 35. Removing a Cooling Module (1) Chapter 6. Module replacement... -
Page 60: Replacing A Power Supply Unit (Psu)
Figure 36. Removing a Cooling Module (2) Important: The cooling module bay must not be empty for more than two minutes while the enclosure is powered up. Inserting a cooling module 1. Rotate the cooling module so that the black release latch and handle are on the right side. 2. -
Page 61: Removing A Psu Module
Figure 37. Removing a PSU module (1) Figure 38. Removing a PSU Module (2) Important: The PSU module bay must not be empty for more than two minutes while the enclosure is powered up. Chapter 6. Module replacement... -
Page 62: Replacing An Sbb I/O Module
Inserting a PSU 1. Ensure the PSU is switched off. 2. Rotate the PSU so that the red release latch and handle are on the left side. 3. Slide the PSU into its slot until the latch clicks home. 4. Connect the AC power cord. 5. -
Page 63: Removing A Module
Figure 40. Removing a module (1). (6Gb/s SAS EBOD module shown) Figure 41. Removing an I/O module (2) Chapter 6. Module replacement... - Page 64 4. Pull the module out of the enclosure (2). Important: The SBB I/O module bay must not be empty for more than two minutes while the enclosure is powered. Inserting an SBB I/O module 1. Rotate the SBB I/O module so that the release latch is at the bottom. 2.
-
Page 65: Appendix A. Technical Specifications
Fully populated enclosure Drive carrier Cooling module Components (fully populated) The table shows the components that populate the enclosure. Table 10. Components Component Quantity Drawers Disk Drives In Carriers (DDICs) SBB I/O module PSUs Cooling modules © Copyright IBM Corp. 2017... -
Page 66: Thermal
Thermal The table shows the specifications for the thermal sensors. Table 11. Thermal specifications Specification Quantity Thermal sensors 2 per sideplane (2 sideplanes per drawer) 2 per drawer baseplane (front) 1 per drawer baseplane (middle/rear) 2 per power supply Number in SBB I/O module is dependent on module type Airflow with all fans running 120 liters/second maximum Temperature and humidity... -
Page 67: Supported Drives
Table 14. Supported drives for enclosure Type Description Hard disk drives (HDD) 4TB Enterprise HDD (IBM Part number: 00LY449) 8TB Enterprise HDD (IBM Part number: 00LY450) 10TB Enterprise HDD (IBM Part number: 00LY453) Solid State Drives (SSD) 800GB SDD (IBM Part number: 00LY451) Shock and vibration tolerance The table shows the shock tolerance for the enclosure. - Page 68 Installation and User Guide - Model 084...
-
Page 69: Appendix B. Standards And Regulations
Individual shelves and towers comply with United States CFR47 Part 15: Radio Frequency Devices, Subpart B: Unintentional Radiators, Class A Class A labeling is used. Harmonics EMC harmonics are in accordance with EN 61000-3-2:2014. Flicker EMC flicker is in accordance with EN 61000-3-3:2013. © Copyright IBM Corp. 2017... -
Page 70: Safety
Environmental and Recycling RoHS and JIG A The IBM ESS expansion Model 084 enclosure is manufactured from RoHS compliant materials and components, in accordance with EU Directives 2002/95/EC and 2011/65/EU. Additionally, this enclosure does not contain any substances or materials listed in Annex A of Joint Industry Guide JIG-101, Material Composition Declaration for Electronic Products (also known as 'JIG A Materials'). - Page 71 The IBM ESS expansion Model 084 enclosure has been designed to comply with this directive in the future. An Environmental Impact Assessment (EIA) has been completed to provide information to support future compliance.
-
Page 72: Acoustics
Packaging The IBM ESS expansion Model 084 enclosure complies with the Packaging (Essential Requirements) Regulations 2003. The design minimizes the amount of packaging used, and the packaging is designed for reuse, recovery or recycling, to reduce the environmental impact of packaging waste. -
Page 73: Notices
Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead. -
Page 74: Trademarks
IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business Machines Corp., registered in many jurisdictions worldwide. Other product and service names might be trademarks of IBM or other companies. A current list of IBM trademarks is available on the Web at “Copyright and trademark information” at www.ibm.com/legal/copytrade.shtml. -
Page 75: Electronic Emission Notices
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors, or by unauthorized changes or modifications to this equipment. -
Page 76: Germany Electromagnetic Compatibility Directive
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der IBM verändert bzw. -
Page 77: People's Republic Of China Class A Statement
People's Republic of China Class A Statement Taiwan Class A Statement Taiwan Contact Information This topic contains the product service contact information for Taiwan. IBM Taiwan Product Service Contact Information: IBM Taiwan Corporation 3F, No 7, Song Ren Rd., Taipei Taiwan Tel: 0800-016-888... -
Page 78: Japan Voluntary Control Council For Interference (Vcci) Notice
This statement applies to products less than or equal to 20 A per phase. This statement applies to products greater than 20 A, single phase. This statement applies to products greater than 20 A per phase, three-phase. Japan Voluntary Control Council for Interference (VCCI) Notice This explains the Japan Voluntary Control Council for Interference (VCCI) statement. -
Page 79: Russia Electromagnetic Interference Class A Statement
This product may not be certified in your country for connection by any means whatsoever to interfaces of public telecommunications networks. Further certification may be required by law prior to making any such connection. Contact an IBM representative or reseller for any questions. Notices... - Page 80 Installation and User Guide - Model 084...
- Page 82 IBM® Printed in USA SC27-4628-01...