Binatone 410 User Manual

Spirit 410 Corded Telephone
Unpacking your phone
In the box you will find:
•
Base Unit
•
Handset
•
Coiled Handset cord
•
Telephone line cord
for Base unit
•
User manual
Keep the packing
materials in a safe
place in case you later
need to transport
the unit
Keep your sales (till)
receipt, which is your
guarantee.
1. LCD Screen
2. Ringer light indication
3. M1,M2,M3 Memory buttons
4. Scroll Up & Down buttons
5. Delete button
6. Set/Store button
7. Memory button
8. LNR(Last Number Redial) button
9. Speakerphone button
10. Mute button
11.R(Recall) button
12.Pause button
Important note---back up batteries
The Spirit 410 requires 2 x 1.5V AAA size Alkaline batteries
installed into the battery compartment before use.
Warning: The caller display will not work without batteries
installed.
2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the telephone line cable will reach your telephone line socket or extension socket.
it is not close to a sink, bath or shower, or anywhere else where it might get wet.
it is not close to other electrical equipment - fridges, washing machines,
microwave ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset cord into the Handset.
Plug the other end into the jack on the left
side of the Base unit.
3. Place the Handset in the Base unit.
Always use the
telephone line
4. Plug the telephone line cord
cord supplied
with your free end into a modular wall jack.
Spirit 410 phone.
Press the cable into the groove so
Other telephone
that the Base unit stands level.
line cords may
not work.
to Modular 5. Lift the Handset and check
Wall jack
for Dial tone in the earpiece.
Installing (or Replacing) the Battery
IMPORTANT - Before removing the battery compartment cover,always
make sure the base unit is disconnected from the telephone line.
Install 2 pcs of Alkaline AAA batteries into the battery compartment and
place back the cover before use.
Note: 1) Please do NOT use Rechargeable batteries in this phone.
2)
1
will show up of the
2
3
4
5
SIZE
6
SIZE
7
8
9
10
11
3. Desk/Wall mount installation
12
Desk Mount To place the Spirit 410 on a desk, connect
the bottom of the phone in the slots near the rear of the base
as shown below .
Insert the rigid clips of the stand into the slots
the phone (near the rear of
the flexible clips clicks into place.
To remove the stand, (1) pinch the flexible clips, (
the stand, and then (3) slide up and forward (3) as shown below.
To place the Spirit 410 on a wall, connect
Wall Mount
bottom of the phone in the
cover as shown
Desk/Wall mounting continue...
Insert the rigid clips of the stand into the slots on the bottom of
the phone (
Make sure the plugs the flexible clips clicks into place.
click into place.
To remove the stand, (1) pinch the flexible
the stand, and then (3) slide up and forward as shown below.
and 08453459677
inatone online
Mark two points on the wall that are 92mm apart to lay the
fixing centers as shown below.
AAA SIZE AAA
AAA SIZE AAA
4. Setting up your phone
Press the SET/STO button to enter the menu
the stand to
through the following options:
SET 1 DATE
Note: The system will time out if you leave
Set Time/Date
on the bottom of
the base). Press down firmly until
2) pull back
the stand to the
slots near the front of the base
below.
Setting up continue...
near the front of the base). Press down firmly until
Set LCD
clips, (2) pull back
Contrast
0818762092 0 3
.com/
BE CAREFUL to check that there are no electrical wires hidden
Fix two screws (supplied with the unit) at the marked locations,
approximately 7mm
between the wall and the the screw head.
Hang the cradle unit on the screws using the wall mount slots.
You may need to remove the telephone from the wall and tighten the
that the cradle is securely fixed and does not wobble . Place the Handset on the
cradle with the parking hook on the cradle arranged to fit in the parking recess
under the earpiece on the Handset.
and then use UP or DOWN
SET 2 LCD SET 3 FLASH
more than 8 seconds between key presses.
You will need to set the correct time and date
displayed correctly on the display.
If you subscribe to a Caller Display service, the
will be set automatically on receipt of your first incoming call.
1 In standby mode, press SET/STO button.
The display shows ' SET 1 DATE '.
2 Press SET/STO button to confirm.
The 'year' icon will be blinking.
3 Press UP or DOWN button to set the year.
4 Press SET/STO button to confirm.
The 'month' icon will be blinking.
5
Press UP or DOWN button to set the month.
6
Press SET/STO button to confirm.
The 'date' icon will be blinking.
7
Press UP or DOWN button to set the date.
8 Press SET/STO button to confirm.
The 'hour' icon will be blinking.
9
Press UP or DOWN button to set the hour.
10 Press SET/STO button to confirm.
The 'minute' icon will be blinking.
11
Press UP or DOWN button to set the minute.
12 Press SET/STO button to confirm the setting.
The display shows ' SET 2 LCD ' , you can
programming,
or press DELETE button to return to standby mode.
In standby mode, press SET/STO button.
1
The display shows ' SET 1 DATE '.
2
Press UP or DOWN button until the display
3
Press SET/STO to confirm.
4 Press UP or DOWN button to select your
viewing level (1~8). The default setting is 3.
5 Press SET/STO button to confirm the setting.
The display shows ' SET 2 LCD ' , you can
programming, or press DELETE button to return to standby mode.
in the wall.
leaving
screws so
buttons to cycle
so they can be
time and date
continue with
shows 'SET 2 LCD'.
comfortable display
continue with