Roland GR-30 Manual page 91

Effect 1 (Reverb Send Level)
STATUS SECOND THIRD
BnH 5BH vvH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value :00H - 7FH (0 - 127)
* Can be received only through the Basic channel.
Program Change
STATUS SECOND
CnH ppH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
pp=Program Number :00H - 7FH (0 - 127) 0=Prg.1 127=Prg.128
* Can be received only through the Basic channel.
* The recognized Program Change number corresponds to each patch as follows,
<When the patches of group A, B, C or D are selected...>
1... 4 = A11...A14 65...68 = C11...C14
5... 8 = A21...A24 69...72 = C21...C24
9...12 = A31...A34 73...76 = C31...C34
13...16 = A41...A44 77...80 = C41...C44
17...20 = A51...A54 81...84 = C51...C54
21...24 = A61...A64 85...88 = C61...C64
25...28 = A71...A74 89...92 = C71...C74
29...32 = A81...A84 93...96 = C81...C84
33...36 = b11...b14 97...100 = d11...d24
37...40 = b21...b24 101...104 = d21...d24
41...44 = b31...b34 105...108 = d31...d34
45...48 = b41...b44 109...112 = d41...d44
49...52 = b51...b54 113...116 = d51...d54
53...56 = b61...b64 117...120 = d61...d64
57...60 = b71...b74 121...124 = d71...d74
61...64 = b81...b84 125...128 = d81...d84
* When you call the patches of the Group E,F,G or H, send the value "1" of the controller
number 0 before the program change message sending.
<When the patches of group E, F, G or H are selected...>
1... 4 = E11...E14 65...68 = G11...G14
5... 8 = E21...E24 69...72 = G21...G24
9...12 = E31...E34 73...76 = G31...G34
13...16 = E41...E44 77...80 = G41...G44
17...20 = E51...E54 81...84 = G51...G54
21...24 = E61...E64 85...88 = G61...G64
25...28 = E71...E74 89...92 = G71...G74
29...32 = E81...E84 93...96 = G81...G84
33...36 = F11...F14 97...100 = H11...H24
37...40 = F21...F24 101...104 = H21...H24
41...44 = F31...F34 105...108 = H31...H34
45...48 = F41...F44 109...112 = H41...H44
49...52 = F51...F54 113...116 = H51...H54
53...56 = F61...F64 117...120 = H61...H64
57...60 = F71...F74 121...124 = H71...H74
61...64 = F81...F84 125...128 = H81...H84
* When you call the patches of the Group A,B,C or D, send the value "0" of the con-
troller number 0 before the program change message sending.
Pitch Bend Change
STATUS SECOND THIRD
EnH llH mmH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
mm,ll=Value :00H,00H - 7FH,7FH (-8192 - +8191)
Channel Mode Message
All Note Off
STATUS SECOND THIRD
BnH 7BH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Turn off all notes that are now on .
OMNI OFF
STATUS SECOND THIRD
BnH 7CH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Will act the same as All Note Off.
OMNI ON
STATUS SECOND THIRD
BnH 7DH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Will act the same as All Note Off
MONO
STATUS SECOND THIRD
BnH 7EH mmH
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
mm=Number of Individual Channels :ignored
* Can be received only through the Basic channel.
* Will act the same as All Note Off
POLY
STATUS SECOND THIRD
BnH 7FH 00H
n=MIDI Channel Number :0H - FH (0 - 15) 0=ch.1 15=ch.16
* Can be received only through the Basic channel.
* Will act the same as All Note Off.
System Realtime Message
Active Sensing
STATUS
FEH
* Having received this massage, GR-30 expects to receive information of any status of
data during about 420msec. If GR-30 doesn't receive any massage during that time, it
acts as if the All Note Off massage is received, and returns to normal operation (will
not check interval of massages).
Timing Clock
STATUS
F8H
* Can be received only when the A-TEMPO is set to "Syn".
Start
STATUS
FAH
* Can be received only when the A-TEMPO is set to "Syn" and the realtime recording of
arpeggiater is ready.
Continue
STATUS
FBH
* Can be received only when the A-TEMPO is set to "Syn" and the realtime recording of
arpeggiater is ready
Stop
STATUS
FCH
* Can be received only when the A-TEMPO is set to "Syn" and the realtime recording of
arpeggiater is ready
System Exclusive Message
STATUS DATA BYTES
F0H iiH ddH ............eeH
F7H
F0H :System Exclusive
ii = Manufacturer ID :41H ( 65 )
dd ......ee = Data : 00H - 7FH ( 0 - 127 )
F7H : EOX (End of Exclusive)
* Refer to Section 3, 4, and the pages of "Roland Exclusive Message" for more detailed
information.
93